Sullair LS16T Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 112

background image

Section 5

OPERATION

35

• Units

- English or metric units may be

selected.

• Communications ID #

- This is the network

address of a machine. If there is more that
one machine connected to the network,
each machine must have a unique number

• Communications baud rate

- This should

always be selected to 9600 baud for all
sequencing modes. It may be lower for
slave or monitoring modes.

• Sequence method

- This parameter sets

the method used for sequencing. The choic-
es are DISABLED, REMOTE, SLAVE,
HOURS, COM ID#. See the Sequencing &
Protocol Manual (P/N 02250057-696) for
details about these modes.

• Drain interval

- The time between actuation

of the drain valve.

• Drain time - The amount of time that the

drain valve is actuated.

• Last Communication Number

- Used only

for sequencing, see Sequencing & Protocol
Manual for details.

• Lowest Allowable Pressure

- Used only for

sequencing, see Sequencing & Protocol
Manual for details.

• Recovery Time

- Used only for sequencing,

see Sequencing & Protocol Manual for
details.

• Rotate Time

- Used only for sequencing,

see Sequencing & Protocol Manual for
details.

• Machine Capacity

- Used only for sequenc-

ing, see Sequencing & Protocol Manual for
details.

• Sequence Hours

- Used only for sequenc-

ing, see Sequencing & Protocol Manual for
details.

5.4 OPERATING THE COMPRESSOR

Before operating the compressor the operating
parameters must be setup. See the previous sec-
tion on operating parameter setup.

MANUAL OPERATION MODE

In this mode the compressor will run indefinitely, as
long as temperatures and pressure remain within
the valid operating ranges, and the motor overload
or emergency stop contacts are not tripped.

Pressing the “

” will turn on the compressor

and put it in manual mode. If the compressor is
already running, but in automatic mode, pressing

“

” will switch operation to manual. Pressing

“

” while already running in manual mode will

cause the Supervisor to turn off the common fault
relay, if engaged, and clear any maintenance indi-
cators.

To stop the compressor, press “

”. If the com-

pressor is already off when “

” is pressed, the

SEQ HRS

1000

CAPACITY

100

ROTATE

50

RECOVER

10 SEC

LOWEST

90 PSI

LAST COM

3

DRN TIM

1 SEC

DRN INTV

10 MIN

SEQUENCE

HOURS

BAUDRATE

9600

COM ID #

1

UNITS

ENGLISH

«
...
39
40
41
42
43
...
»

Содержание LS16T

















































































































Отзывы:

Нет отзывов

Похожие инструкции для LS16T

Бренд: Autojack Страницы: 12

Craftsman 919.727560

Бренд: Sears Страницы: 20

Бренд: California Air Tools Страницы: 23

Бренд: Bosch Страницы: 40

Бренд: Sparmax Страницы: 2

Бренд: Global Machine Company Страницы: 16

Бренд: Premier Страницы: 11

Бренд: North American Tool Industries Страницы: 3

Бренд: Bostitch Страницы: 10

Бренд: ACC Страницы: 20

Бренд: Powermate Страницы: 24

Бренд: Gardner Denver Страницы: 60

Бренд: Mi-T-M Страницы: 16

Бренд: Danfoss Страницы: 4

Бренд: Campbell Hausfeld Страницы: 6

Бренд: Danfoss Страницы: 3

ELECTRA-SCREW EBE DD Series

Бренд: Gardner Denver Страницы: 44

Бренд: Metabo Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды