Sullair LS16T Скачать руководство пользователя | Manualshive

Страница: 30 / 112

background image

Section 2

DESCRIPTION

24

If there are alarms active they will alternately be
shown with the default display. The machine status
will be displayed for 2 seconds then the alarms for
2 seconds each. For example:

To view other status press the DSP key. All temper-
atures and pressures may be displayed as well as
other status information. To scroll through the dis-
plays press the up arrow or down arrow keys. Up
arrow moves to the next display, down arrow the
previous display. To return to the default display
press the display key.

•

Separator differential pressure and the max-

imum limit. If the limit is exceeded, a sepa-
rator maintenance warning will be dis-
played.

•

Sump pressure and line pressure.

•

Oil filter differential pressure and the maxi-
mum limit. If the limit is exceeded oil main-
tenance warning will be displayed.

•

Pressure before (P4) and after (P3) oil filter.

•

Oil differential pressure and the minimum

limit. If the pressure goes below the limit a
P3 LOW shutdown will occur. Oil differential
(dP3) is defined as P3-P1/2

•

Unit discharge temperature and the maxi-

mum limit. If the temperature exceeds the
limit a T1 HI shutdown will occur.

•

Dry side discharge temperature and the

maximum limit. If the temperature exceeds
the limit a T2 HI shutdown will occur.

•

Oil temperature and the maximum limit. If

the temperature exceeds the limit a T4 HI
shutdown will occur.

•

Total hours that the compressor has been

running.

•

Total hours that the compressor has been

loaded.

•

Last fault log. This shows the fault on the

first line and the run hours when the fault
occurred.

•

Next to last fault log. This shows the fault on

the first line and the run hours when the fault
occurred.

2.11 LAMP INDICATORS

Embedded into the front panel schematic of the
compressor are several lamps. Pressing the lamp
test key will light all the lamps for 3 seconds. Each
LED lamp has the following purpose.

P1

- (Line pressure) If lit steady, signifies that P1 is

being displayed, if flashing denotes the presence of

T1 HI

@2 224

T1 HI

@1 255

HRS LOAD

000987.0

HRS RUN

001234.0

T4 210

MAX 255

T2 210

MAX 255

T1 210

MAX 255

dP3 40

MIN 1

P3 290
P4 295

dP2 4

MAX 20

P1 363
P2 358

dP1 4

MAX 10

T1 HI

360 220

STOP

360 220

«
...
28
29
30
31
32
...
»

Содержание LS16T

















































































































Отзывы:

Нет отзывов

Похожие инструкции для LS16T

Бренд: Clarke Страницы: 20

MISTRAL CLASSIC M6-ET

Бренд: Paramina Страницы: 68

Бренд: AirMan Страницы: 80

Бренд: Black Ridge Страницы: 28

Бренд: Bitzer Страницы: 20

Бренд: California Air Tools Страницы: 16

Бренд: Kobalt Страницы: 8

Бренд: Kobalt Страницы: 8

Бренд: DV Systems Страницы: 27

JEFC100V10B Series

Бренд: Jefferson Страницы: 20

Бренд: MasterCraft Страницы: 25

Бренд: Clarke Страницы: 8

Бренд: Clarke Страницы: 20

Бренд: Clarke Страницы: 16

Бренд: Clarke Страницы: 20

Бренд: Atmos Страницы: 44

Бренд: Atmos Страницы: 51

Бренд: Chicago Pneumatic Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды