Sukup Fastir Скачать руководство пользователя страница 21

Страница: 21 / 70

Assembly & Installation

IV.

Installing Tilt Switches

For part numbers and descriptions of parts
referenced in this section, see parts assembly
manual, page 53.

23 Bolt junction box with attached tilt switch onto

bottom of motor side of primary carriage using

5/16” x 1” bolts (pointing out through carriage) and

5/16” lockwashers and nuts provided on junction

box. Tighten using 1/2” wrench.

Figure 16

-Tilt Switch Placement on Primary Carriage

24 On satellite and stationary outside carriages (if

present), bolt tilt switches to bottom auger side

of carriages near down auger slots (facing in).

Use 5/16” x 1” bolt pointing down through plate

and 5/16” lockwasher and nut.

Figure 17

-Tilt Switch Placement on Satellite and

Stationary Carriages

25 Align tilt switch with carriage edge and tighten

using 1/2” wrench.

Installing Motors

For part numbers and descriptions of parts
referenced in this section, see parts assembly
manual, page 53.

26 Slide springs from hardware sack onto each rod

on motor mount(s).

Figure 18

-Motor Installation

27 Bolt appropriate motor for each carriage onto

motor mount with motor pulley facing up. Use

5/16” x 1” bolts and 5/16” flatwashers,

lockwashers, and nuts and tighten with 1/2”

wrench.

Figure 18

28 Slide motor mount rods though tubes welded onto

carriages from outside of carriage.

Figure 18

29 Attach motor mount to carriage by inserting

hairpin clips from hardware sack into holes on

ends of motor mount rods.

Figure 18

DANGER!

Failure to secure motor mount with

hairpin clips could result in motor falling off

machine if belt is not attached, causing death or

serious injury.

29.1

Note:

Sequences of motors (beginning

with primary carriage and moving

outward) are as follows (see page 69 for

motor component numbers):



Single-Auger Machine

: S



Double-Auger Machine

: A-O



Triple-Auger Machine, Single Phase

: A-O-O



Triple-Auger Machine, Three Phase

: A-B-O



Quadruple-Auger Machine

: A-O-B-O



Quintuple-Auger Machine

: A-B-O-B-O

Содержание Fastir







































































Результаты поиска

Содержание Fastir

Отзывы:

Похожие инструкции для Fastir

Бренды по названию

Популярные бренды

Sukup Fastir, Инструкция и каталог запасных частей для владельца

Результаты поиска

Содержание Fastir

Отзывы:

Похожие инструкции для Fastir

Бренды по названию

Популярные бренды