manualshive.com logo in svg

Sub-Zero 424FS, Руководство по обслуживанию

Поделиться
Скачать
Sub-Zero 424FS Скачать руководство пользователя страница 9

Page 9

400 Series

400 Series

Component Access and Removal

6-9

Evaporator Support Cover Access and Removal
(Model 424)

The evaporator support covers are narrow covers to the
left and right of the lower evaporator cover.  The left
cover hides the upper compartment drain line and the
right cover is over the evaporator thermistor.  These
covers are held in place by screws under the lower
evaporator cover.
To remove the evaporator support covers, you must first
remove the three wine racks, all cabinet slides, cabinet
slide spacers and cabinet slide support spacers in the
lower compartment.  Then, remove the evaporator fan
cover mounting screws, the evaporator fan cover and
the lower evaporator cover.  Extract the evaporator sup-
port cover mounting screws and pull the evaporator
support cover out.  

(See Figure 6-15)

Figure 6-15.

Evaporator Support Cover Removal

MODEL 424 INTERIOR MECHANICAL 

COMPONENT ACCESS AND REMOVAL:

An attempt has been made to arrange these instruc-
tions in such a way as to simulate which components
would need to be removed first in order to gain access
to other components.  When following a component
removal procedure, it may be necessary to reference
another removal procedure towards the front of this
section.

Control Board Access and Removal  (Model 424)

NOTE:

 

See ELECTRIC SHOCK WARNING at begin-

ning of this section.

  Also 

see STATIC ELECTRICITY

CAUTION at beginning of this section.

The control board is located on the bottom side of the
compartment divider, directly behind the control panel,
and is concealed by an access panel.  The control
board is held in place by four tabs, one at each corner
of the board.
To get to the control board you will need to extract the
two screws at the back of the access panel, then lower
the back of the access panel and pull it towards the
rear of the unit.  

(See Figure 6-16)

To remove the control board, disconnect the LED ribbon
cable, the membrane switch ribbon cable, and all other
electrical leads attached to the control board.  Expand
the tabs to release the control board, then pull down
and out.  

(See Figure 6-17)

NOTE:

 

When re-connecting electrical leads to the con-

trol board, be sure the the silver area on the membrane
switch ribbon cable terminal is facing away from the
control board.

Figure 6-16.  Control Board Access Panel

Figure 6-17.  Control Board

Evaporator Support Covers

Mounting screws 
concealed by 
evaporator cover

Tab

LED Ribbon Cable

Membrane

Switch 

Ribbon Cable

Electrical
Connections

Tab

Tab

Tab

Access Panel

Содержание 424FS








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды