manualshive.com logo in svg

Sub-Zero 424FS, Руководство по обслуживанию

Поделиться
Скачать
Sub-Zero 424FS Скачать руководство пользователя страница 22

Page 22

400 Series

400 Series

Component Access and Removal

6-22

MODELS 427 & 427R INTERIOR

MECHANICAL COMPONENT ACCESS AND

REMOVAL:

An attempt has been made to arrange these instruc-
tions in such a way as to simulate which components
would need to be removed first in order to gain access
to other components.  When following a component
removal procedure, it may be necessary to reference
another removal procedure towards the front of this
sub-section.

Wine Storage Control Board Access and Removal
(Models 427 & 427R)

The control board is located at the bottom of the com-
partment divider, behind the control panel, and is con-
cealed by an access panel.  The control board is held in
place by four tabs, one at each corner of the board.

NOTE:

 

See ELECTRIC SHOCK WARNING and STAT-

IC ELECTRICITY CAUTION at beginning of this sec-
tion.

To get to the control board you will need to extract the
two screws at the back of the access panel, then lower
the back of the access panel and pull it towards the
rear of the unit.  

(See Figure 6-48)

Figure 6-48.

Wine Storage Control Board Access Panel

Refrigerator Section Evaporator Support Cover
Access and Removal  (Model 427R ONLY)

The evaporator support covers are narrow covers to the
left and right of the refrigerator evaporator cover.  The
left cover holds the control cable connector.  These cov-
ers are held in place by screws under the refrigerator
evaporator cover.
To remove the evaporator support covers, you must first
remove the drawer slides and both drawer closers.
Then, remove the evaporator fan cover mounting
screws, the evaporator fan cover and the refrigerator
evaporator cover.  Extract the evaporator support cover
mounting screws and pull the evaporator support cover
out.   

(See Figure 6-47)

NOTE: 

 

If removing the left evaporator support cover,

the control cable connector must be disconnected as
you remove the cover.

Figure 6-47.  Refrigerator Evaporator

Support Cover Removal

Evaporator Support Covers

Mounting screws 
concealed by 
evaporator cover

Access Panel

Содержание 424FS








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды