manualshive.com logo in svg

Sub-Zero 424FS, Руководство по обслуживанию

Поделиться
Скачать
Sub-Zero 424FS Скачать руководство пользователя страница 35

Page 35

400 Series

400 Series

Component Access and Removal

6-35

Upper and Lower Evaporator Fan Cover Removal
(Model 430)

There are two access holes in the front of the evapora-
tor fan cover.  The back flanges of the evaporator fan
cover have slots that line up with the access holes.
Screws inside these access holes pass through slots in
the back flanges and through holes in the evaporator
cover into screw grommets, securing the fan cover.
To remove the evaporator fan cover, extract the two
mounting screws from the access holes and pull the fan
cover forward.  

(See Figure 6-78)

NOTE:

 

When reinstalling the fan cover, first insert one

of the two mounting screws through the evaporator
cover, into the screw grommet, but do not fully tighten.
Then, slide the corresponding slot in the rear flange of
the fan cover over the screw and rotate the fan cover
up until the other access hole lines up with the other
mounting hole.  Insert the second screw and tighten
both screws.

Upper and Lower Evaporator Cover Removal
(Model 430)

To remove the upper and lower evaporator covers, you
must first remove the wine racks in the compartment.
Then, remove the evaporator fan cover mounting
screws and the evaporator fan cover.  Pull the top of
the evaporator cover forward and down and lift off of
pegs at bottom.   You'll find a ground wire riveted to the
back of the evaporator cover, and the other end  has a
screw securing it to the rear wall.  Extract the ground
screw and pull the evaporator cover out..  

(See Figure

6-79)

NOTE:

  

When reinstalling the evaporator cover, the

ground wire must be reattached with the ground screw
to the rear wall.

Evaporator Support Cover Removal  (Model 430)

The evaporator support covers are narrow covers to the
left and right of the evaporator covers.  These covers
are held in place by screws under the lower evaporator
cover.  
To remove the evaporator support covers, you must first
remove the wine racks, all cabinet slides, cabinet slide
spacers and cabinet slide support spacers in the com-
partment.  Then, remove the evaporator fan cover
mounting screws, the evaporator fan cover and the
evaporator cover.  Extract the evaporator support cover
mounting screws and pull the evaporator support cover
out.  

(See Figure 6-80)

Figure 6-78.  Evap Fan Cover Removal

Figure 6-79.

Evaporator Cover Removal

Figure 6-80.

Evaporator Support Cover Removal

Duct opening at top

Evaporator Fan Cover

Screw Access Hole

Evaporator Cover

Ground Screw

Evaporator Support Covers

Mounting screws 
concealed by 
evaporator cover

Содержание 424FS








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды