manualshive.com logo in svg

Style selections SSFBD28T, Руководство пользователя

Поделиться
Скачать
Style selections SSFBD28T Скачать руководство пользователя страница 21

21

LIGHTING INSTRUCTIONS

Unscrew ignitor cap and install a AAA battery (included) with the + pointing out. Replace cap.

1. 

STOP!

 Read the safety information on page 20.

2. 

Warning

: You must operate this heater with the screen in place. Make sure screen is installed 

 

before running heater.

3. Turn control knob clockwise to the OFF position, see Fig. 19, page 22.

4. Wait five (5) minutes to clear out any gas. Then smell for gas around heater and near floor. If 

  you smell gas, 

STOP

! Follow "B" in the safety information on Warnings plate. If you don't 

  smell gas, go to the next step.

5. Turn control knob counterclockwise to the PILOT position. Keep control knob pressed in for 

  five (5) seconds. 

Note

: You may be running this heater for the first time after hooking up to gas 

  supply. If so, the control knob may need to be pressed in for 30 seconds. This will allow air to 

  bleed from the gas system. If control knob does not pop up when released, contact a qualified '

  service person or gas supplier for repairs.

6. With control knob pressed in, push down and release ignitor button. This will light pilot.The 

  pilot is attached to the rear of the front burner. If needed, keep pressing ignitor button until pilot 

  lights. 

Note

: If pilot does not stay lit, contact a qualified service person or gas supplier for 

  repairs. Until repairs are made, light pilot with match.

7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release 

  control knob. 

Note

: If pilot goes out, repeat steps 3 through 7. This heater has a safety 

  interlock system. Wait one (1) minute before lighting pilot again.

8. 

WARNING

: Make sure that while the input gas type is NG, pilot burner NG ignites; while the 

  input type is LP, pilot burner LP ignites. Note: If you find anything abnormal in this step, repeat 

  steps 2 through 8.

9. Turn control knob counterclockwise to the desired heating level. The main burner should light. 

  Set control knob to any heat level between HI and LO (5 –1).

THERMOSTATIC CONTROL OPERATION

The thermostatic control used on this model differs from standard thermostats. Standard

thermostats simply turn the burner on and off. The thermostat used on this heater senses the 

room temperature. At times the room may exceed the set temperature. If so, the burner will shut 

off. The burner will cycle back on when room temperature drops below the set temperature. The 

control knob can be set to any comfort level between HIGH (5) and LOW (1).

Note

: The thermostat sensing bulb measures the temperature depending on housing 

construction.

Содержание SSFBD28T
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды