Studio Technologies Dante 5422A Скачать руководство пользователя страница 42

Страница: 42 / 65

Issue 3, December 2022

Model 5422A User Guide

Page 42

Studio Technologies, Inc.

Model 5422A

DANTE INTERCOM AUDIO ENGINE

Manual Gateway:

This field is grayed out when the

IP configuration mode is selected for

Automatic

This field will be display-only in this instance and will

show an IPv4 gateway IP address in dot-decimal

notation (four octets separated by dots) if the current

IP address and related network parameters were

obtained by way of DHCP. This is the gateway IP

address that is being used by the Model 5422A’s man-

agement web server.

If the IP address configuration mode is selected for

Automatic

and the current IP address was obtained by

way of link-local no gateway IP address will be shown

in this field. This is because no gateway IP address is

associated with link-local.

When the IP configuration mode is selected for

Manual

the gateway IP address field will not be grayed out. In

this situation, the stored gateway IP address will be

shown and can be modified as desired to meet the

requirements of the application.

The shown value is the gateway IP address that is

currently in use, or will be used at the time of the

next Ethernet management connection reboot. After

entering a gateway IP address using the standard

dot-decimal notation format (four octets separated by

dots) the submit button must be pressed for a change

to be stored. A system reboot is required for the

revised gateway IP address to be utilized. Restoring

the Model 5422A’s default values will not change the

stored gateway IP address value.

Submit:

A submit button is located near the bottom of

the Network menu webpage. For any changes made

to fields to the Network configuration to be saved the

submit button must be pressed.

Содержание Dante 5422A


































































Результаты поиска

Содержание Dante 5422A

Отзывы:

Бренды по названию

Популярные бренды

Studio Technologies Dante 5422A, Руководство пользователя

Результаты поиска

Содержание Dante 5422A

Отзывы:

Бренды по названию

Популярные бренды