Studer D424, Инструкция по эксплуатации и обслуживанию

Страница: 102 / 189

D424 MO Recorder
Date printed: 22.02.02 SW V 1.6
Troubleshooting E5/1
5 TROUBLESHOOTING
5.1 Error Messages
Operation and con-
figuration errors:
Problem: Solution:
"CD not suitable" Inserted disc cannot be used for selected transfer
Insert empty CD-R for TOC transfer, or not yet finalized
CD-R for ADD transfer
"Check take distance" CD transfer tried with at least 1 take below 4 s audio Modify corresponding take to more than 4 s
"Clk.RefDk DiskH"
"Clk.RefDk DiskHD"
"Clk.RefHk DiskD"
"Clk.RefHk DiskDD"
Format of external reference signal (Clk.Ref) does not
correspond to sampling rate (Disk)
H = 48, HD = 48drop, D = 44.1, DD = 44.056
Select correct configuration
"Cmd not allowed" Command could not be accepted temporarily
Some system utilities and configuration settings dis-
abled in play and recording modes, stop D424 first
"Disk not empty"
When trying to do DISK COPY, target disk was found
not empty
Reformat target disk before doing a DISK COPY
"Disk performance"
1.2/1.3 GB disk not capable of performing insert re-
cording with 29/24 bit resolution
Select 16 bit resolution or use 2.3/2.6 GB Disk
"Disk write protected" Disk protected with "write protect" tab Move tab to "rec enable" position
"Drive is busy"
SCSI operation failed because corresponding device is
in use
Stop D424 before switching SCSI devices
"Drive not mounted" D741 CD drive not ready for transfer
• Insert appropriate CD-R
• Check for correct SCSI wiring
"Drive not supported"
SCSI drive has been connected to a D424 currently not
supported
Remove SCSI device
"Editing in fade area" Editing in fade area not allowed
Move edit points, or modify previously made edit that
generates particular fade area
"Emphasis mismatch"
Attempt to add a take with an emphasis status different
from the previously recorded sequence All takes of a sequence should be recorded with the
same emphasis status.
"Invalid edit points"
Edit points IN and OUT beyond the sequence limits, or
IN > OUT
Set correct edit points
"Invalid rec points"
Edit points IN and OUT for AutoRecord mode beyond
the sequence limits, or IN > OUT
Set correct edit points
"ISRC error"
ISRC entry not complete, or corresponding take infor-
mation corrupted
Check data
"Last rec nr reached" Attempt to record more than 99 sound files Try to remove unused audio files with a Cleanup
"Low diskcopy space"
Current sequence (TOC mode) or take (ADD) longer
than available space on CD-R
Adjust sequence length to disc, or use new disc
"Max tk/Ix nr reached"
Attempt to create take or index number greater than
maximum (99) Remove old unnecessary markers and renumber
sequence
"Mismatch TC format"
Timecode format at TC input not corresponding to
internal TC format
Select correct TC format
"No record space left" No space left for new recording session Try to remove unused audio files with CLEANUP
"Nothing to UNDO"
Last edit process cannot be undone, because of:
• Sequence processes since the last edit
• Not in edit mode
• -
• Switch to edit mode with SOURCE/TARGET
"One Smplrate on disk" Attempt to switch sampling rate within recorded disk
Only one sampling rate allowed per disk side – re-
format disk to change sampling rate
"Reg val out of range"
Locate was tried with corresponding register contents
beyond current sequence range
Modify register
"Smplrate not 44.1kHz"
CD transfer was tried, but source sequence has not
44.1 kHz sampling rate
CD transfers only possible with 44.1 kHz sampling rate
"UPC error"
UPC entry invalid, or inserted CD-R already has valid
UPC code
Check data or replace disc
"Wrong copy params"
Copy parameter is not valid for current copy configura-
tion
Check copy target and parameters
"Wrong SCSI id select"
Copy process cannot be performed with currently
selected target drive (e.g. work copy to CD-R)
Check copy target and parameters