Stryker TriaDyne III Proventa 2030 Скачать руководство пользователя страница 33

Страница: 33 / 113

Service Information

SCALE SYSTEM DIAGNOSTICS AND CALIBRATION

Diagnostic Mode Functions:

1. ANGLE CALIBRATE

−

This may be required in the field to recalibrate the scale. Calibrate using 50

pounds.

2. DISP. CORNER LBS

−

This function displays the individual corner weights in

pounds

for each load cell

and can be used to isolate a defective load cell.

3. DISP. CORNER CTS

−

This function displays the individual corner weights in

counts

for each load cell

and can be used to isolate a defective load cell.

4. DISPLAY FACTORS – This function is used to see the scale calibration factors. This can be used to

diagnose a bad scale calibration.

5. DISPLAY AVERAGES

−

This function is used to see the average weight in pounds each load cell has

experienced.

6. DISPLAY MAXIMUMS

−

This function is used to see the maximum weight each load cell has experi-

enced.

7. CLEAR STATISTICS

−

This function is used to clear the averages and maximums.

8. INIT TO DEFAULTS

−

This function is used to reset the scale factors back to defaults.

9. VIEW ERROR LOG

−

This function can be used to see a log of scale errors and the time they occurred.

10. LOCK/UNLOCK LBS/KG

−

This function can be used to lock out the ability to change weight units.

11. PICK EXIT ALARM

−

This function can be used to select a different bed exit alarm tone.

12. BRAKE ALARM OFF/ON

−

This function can be used to enable or disable an audible alarm when the

brakes are not set. Not available for beds with Zoom or Battery Backup.

13. DEFAULT ANGLE

−

This function can be used to select the default angle displayed to either fowler or

trend.

14. SOFTWARE CONFIG

−

This function can be used to see what the bed configuration is.

15. SOFTWARE VERSION

−

This function can be used to see what software version it is.

16. CALIBRATE SCALE

−

This is the old scale calibration routine with 200 pounds. Only there for backup

purposes.

17. EXIT DIAGNOSTIC

−

This function will give you the ability to exit the diagnostic mode and go into scale

mode.

Diagnostic Mode:
NOTE

It requires

two people

to enable the diagnostic mode for the scale system.

1. To enter diagnostic mode, unplug the bed’s power cord from the wall socket.
2. Press and

hold down

the LBS/KGS button.

3. While still holding the LBS/KGS button, plug the bed’s power cord into the wall socket.
4. After two seconds, release the LBS/KGS button. The scale monitor should read “ANGLE CALIBRATE”.

The diagnostic mode is now active.

Содержание TriaDyne III Proventa 2030


















































































































Результаты поиска

Содержание TriaDyne III Proventa 2030

Отзывы:

Бренды по названию

Популярные бренды

Stryker TriaDyne III Proventa 2030, Руководство по обслуживанию

Результаты поиска

Содержание TriaDyne III Proventa 2030

Отзывы:

Бренды по названию

Популярные бренды