manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Руководство по обслуживанию

Поделиться
Скачать
Stryker TriaDyne III Proventa 2030 Скачать руководство пользователя страница 25

Service Information

24

LIFT MOTOR AND CAPACITOR REMOVAL AND REPLACEMENT

Required Tools:

3/8” Socket w/Extension

5/16” Socket

Floor Jack

Side Cutters

7/16” Open End Wrench

2x4 (or Equivalent)

3/8” Drive Ratchet

1/4” Drive Ratchet

A

B

D

FOOT END

C

Procedure:

NOTE

If you need more space to work under the base frame, place a 2x4 across the base frame rails and use a

floor jack to raise the base frame off the floor.

1. Unplug the bed power cord from the wall socket.  Using a 5/16” socket wrench, remove the five bolts

holding the lower lift cover to the base and remove the cover.

2. Disconnect the two connectors (A) at the motor capacitor.
3. Disconnect the white connector (B) from the power cord.
4. Using side cutters, cut the cable ties holding the capacitor (C) to the base and remove the capacitor.
5. Using a 3/8” socket wrench, remove the four screws (D) holding the motor assembly in the lift housing

and remove the motor assembly.

6. Reverse the above steps to install the new motor.

NOTE

The drive shaft on the new motor probably will have to be turned to be aligned with the coupler.  Use a 7/16”

open end wrench to turn the drive shaft of the motor.

The procedure for lift motor and capacitor removal and replacement is the same for both ends of the bed.

Содержание TriaDyne III Proventa 2030


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды