manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Руководство по обслуживанию

Поделиться
Скачать
Stryker TriaDyne III Proventa 2030 Скачать руководство пользователя страница 10

Introduction

9

BED SYMBOLS

  WARNING

Because individual beds may have different options, foot boards should not be moved from one bed to anoth-

er.  Mixing foot boards could result in unpredictable bed operation.

1. Press repeatedly for low, medium and high settings for the siderail control lights.  Continue to press this

switch to turn off the siderail control lights and the nurse call indicator light.

2. Press to lock out all bed motion controls on the siderails.  Press again to unlock.
3. Press to lock out Back motion control on the siderails.  Press again to unlock.
4. Press to lock out Knee motion control on the siderails.  Press again to unlock.
5. Press to lock out bed up/down motion controls on the siderails.  Press again to unlock.
6. Press to raise bed.
7. Press to lower bed.
8. Press to lower head end of bed (Trendelenburg).
9. Press to lower foot end of bed (Reverse Trendelenburg).

1. Press to raise back section.
2. Press to raise knee section.
3. Press to lower back section.
4. Press to lower knee section.

Содержание TriaDyne III Proventa 2030


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды