manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Руководство по обслуживанию

Поделиться
Скачать
Stryker TriaDyne III Proventa 2030 Скачать руководство пользователя страница 30

Service Information

29

LIFT MOTOR COUPLER REPLACEMENT

Required Tools:

5/16” Socket Wrench

3/8” Socket Wrench (w/6” Extension)

Floor Jack

2x4 (or Equivalent)

B

A

C

Procedure:
NOTE

If you need more space to work under the base frame, place a 2x4 across the base frame rails and use a

floor jack to raise the base frame off the floor.
1. Unplug the bed power cord from the wall socket.
2. Using a 5/16” socket wrench, remove the five bolts holding the lower lift cover to the base and remove

the cover.

3. Using a 3/8” socket with an extension, remove the four bolts (A) holding the isolation plate (B) to the lift

housing and lower the lift motor and isolation plate assembly to allow access to the coupler (C).

4. The motor coupler can now be removed from the lift housing.
5. Reverse the above steps to install the new motor coupler and bushings.

Содержание TriaDyne III Proventa 2030


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды