1600 Watt
Lamp
Installation
ASSEMBLE
THE
REQUIRED
ADAPTERS
to
the
1600
watt
lamp
as
illustrated
prior
to
inserting
the
lamp
into
the
lamphouse.
Be
very
careful
not
to
apply
any
mechanical
strain
to
the
quartz
envelope
when
installing
adapters.
SCREW
THE
THREADED
CATHODE
ADAPTER
(24270000)
onto
the
lamp
stud so it
seats firmly against the shoulder of the cathode (-) end cap. Slip the correct brass anode adapter with
set
screw
over
the
stud
of
the
positive
end
cap
in
contact
with
the
shoulder
of
the
anode
(+)
end
cap.
Tighten
all threaded fasteners securely to insure firm mechanical fit and good electrical conduction.
LOOSEN
THE
THUMB
SCREWS
on
the
top
of
the
front
lamp
support
yoke
and
swing
the
retainer
plate
clear
of
the
yoke.
Slide
the
contact
clamp
of
the
igniter
lead
over
the
brass
socket
of
the
rear
lamp
support
collet.
REMOVE
THE
PROTECTIVE
COVER
from
the
lamp
after
putting
on
the
face
shield.
DO NOT
touch the clear quartz envelope of the
lamp
with bare fingers. Natural skin oils will rapidly
burn
into
the
quartz
and
shorten
lamp
life.
The
xenon
lamp
warranty
does
not
cover
damage
of
this
nature.
If the
quartz is accidentally fingermarked, thoroughly remove the fingerprints with isopropyl alcohol before
igniting
the
lamp
.
INSERT THE
LAMP
into the lamphouse, between the reflector support and the front of the
lamphouse. Pass the anode (+) end of the bulb into the reflector and through the center hole of the reflector.
Take
care
not
to touch or scratch the surface of the reflector.
INSERT
THE
ANODE
ADAPTER
STEM
into
the
rear
support
collet.
The
stem
must
be
inserted
as
far
into
the
socket
as
possible
to
insure
good
conduction
and
to
permit
full
focus
travel
of
the
lamp
.
Place
the
cathode
adapter
stem
into
the
front lamp
support
yoke,
pivot
the
retaining
plate
to
its
closed
position,
and
tighten both thumb screws. Using a 9/64"
A
llen wrench, firmly tighten the socket head
clamping screw in the
positive
(+)
contact
to
insure
a
good
electrical
contact.
INSTALL
THE
NEGATIVE
(-)
LEAD
CONTACT
CLAMP
over
the
end
of
the
cathode
adapter.
Slide the contact up to seat its shoulder firmly against the tip of the cathode adapter. Dress the
negative lead
directly
in
front
of
the
front lamp
support
yoke
to
minimize
the
shadow.
Tighten
the
socket
head
clamping
screw
securely
using
a
9/64"
A
l
len
wrench.
2000 Watt
or higher
Lamp
Installation
REMOVE
THE
PROTECTIVE
COVER
from
the
xenon
lamp
only
if
necessary.
Slide
the
contact
clamp
of
the
igniter
lead
over
the
brass
socket
of
the
rear
bulb
support
collet.
If
the
lamp
is
supplied
by
the
manufacturer
with
an
anode
lead
attached,
remove
the
factory-installed
anode lead. Remove any
fingermarks from the
lamp
envelope with
isopropyl
alcohol.
INSERT
THE
lamp
into
the
lamphouse,
passing
the
anode
(+)
end
through
the
hole in the
reflector. Handle the
lamp
by the metal end caps
only.
Pass
the
anode
pin
as
far
as
possible
to
the
rear
of
the
lamphouse
to
allow
clearance
between
the
cathode
(-)
pin
and
the
front
lamp
support.
Take
care
not
to touch or scratch the surface of the reflector; do not touch the quartz envelope of the
lamp
. Slide the
cathode
(-)
end
cap
through
the
spring-cushioned
ring
of
the
lamp
shock
mount.
ST3
/009
Содержание SUPER TROUPER III
