strex STB-140-10 Скачать руководство пользователя

Страница: 19 / 19

Section 7: Warranty

1. The warranty is for one year, commencing the date the customer receives the

product and includes the instrument casing, non-wearable parts, as well as, the

motor and bearings. The cell culture chambers are considered consumables, Strex

is responsible for repair or replacement of chambers, only if they are received and

found defective.

1. The warranty does not cover damage to the instrument that is a result of the

following circumstances:

①

Damage caused by dropping, or other impact.

②

Damage caused by inappropriate operation of the instrument.

③

Damage resulting from an attempted repair or modification of the

instrument by the user.

④

Damage caused by unavoidable external causes such as earthquakes,

lightening, fire, flood, gas leak, power surges, or other acts of

providence.

3. Strex is free from any responsibility for effects or loss or damages arising from the

result of the machine operation.

This warranty assures that Strex will repair our product free of charge as stipulated in

our warranty policy.

Any shipping charges will be born by buyer.

Strex US Office

10060 Carroll Canyon Rd.,

Suite 100

San Diego, CA 921

Email:

[email protected]

www.strexcell.com

The information contained herein such as specification, configuration, and data or alike
in part or in whole may be subject to change without notice.

SC02-1018

Содержание STB-140-10




















Результаты поиска

Содержание STB-140-10

Отзывы:

Похожие инструкции для STB-140-10

Бренды по названию

Популярные бренды

strex STB-140-10, Руководство пользователя

Результаты поиска

Содержание STB-140-10

Отзывы:

Похожие инструкции для STB-140-10

Бренды по названию

Популярные бренды