background image

16

Operational Concerns

Please make sure to read the manual prior to running the unit. Those who are
not familiar with the machine should not operate it.

Do not put your hand close to mechanical parts or alike while the unit is running.

Do not put any foreign substances inside the machine. Water, metal, or paper in
motor area, may cause fire or electrical shock.

Do not make any attempt to disassemble or modify the machine. Do not remove
the cover in an attempt to touch the mechanism inside, which may cause you an
electrical shock.

Please refrain from modifying the machine without our permission, you may be
shocked or injured. If you do attempt to modify the machine, the warranty on the
unit is void and we will not be responsible for any performance deterioration or
unit malfunction.

In the case of any abnormal sound, smell, or smoke, disconnect the power
immediately and contact Strex.

Do not run the machine overloaded.

Be cautious as to your clothing and hair when operating the instrument. Baggy
clothing, neckties, necklaces, etc., can get tangled in moving parts of the unit.
Take appropriate precautions to prevent this occurrence.

Keep the machine clean and periodically inspect the instrument for excessive
wear or damage. Contact Strex if you have any concerns.

Содержание STB-140-10




















Отзывы: