Strebel S-FX 125, Руководство по установке, эксплуатации и техническому обслуживанию

Страница: 45 / 68

45
10.4.4 T
RANSPARENT
P
ARAMETER
–
P
There is a total of 31 parameters within the transparent parameter.
Each parameter is listed in the below table along with what they are set to as standard.
Index Description Range S-FX 70 S-FX 125 S-FX 220 S-FX 320
P01 Start Up Heat
Output 0
– 100%
30% 30% 30% 30%
P02 Heating Ramp 1-10c / minute 1-10c/min 1-10c/min 1-10c/min 1-10c/min
P03 Min Set Point
Temperature 20c
– 80c
20c 20c 20c 20c
P04 Heating Delay
Time 0
– 10 Minute
4 min 4 min 4 min 4 min
P05 CH Pump Over
Run 0
– 255 Minutes
3 min 3 min 3 min 3 min
P06 Pump Operation 0
– 3
0 0 0 0
P07 Min Modulating
Pump Speed 0
– 100%
30% 30% 30% 30%
P08 Modulating Pump
Start-Up Speed 0
– 100%
75% 75% 75% 75%
P09 Maximum Pump
Modulating Speed 0
– 100%
100% 100% 100% 100%
P10 Pump Shut Down
Temp in Overrun 0
– 100c
35c 35c 35c 35c
P11 Pump Start Up
Temp Hysteresis 0
– 100c
5c 5c 5c 5c
P12 Minimum Heating
Set Point 20
– 90c
20c 20c 20c 20c
P13 Maximum Heating
Set Point 20
– 90c
80c 80c 80c 80c
P14 Maximum Output
in CH Mode 0
– 100%
80% 80% 80% 80%
P15 DHW Ramp 1-10c / minute 5c / min 5c / min 5c / min 5c / min
P16 DHW Delay Time 0
– 255 Seconds
120 120 120 120
P17 DHW Pump
Overrun 0
– 255 Seconds
30 30 30 30
P18 Min DHW
Setpoint With b02 set to 1, 4 or 7
With b02 set to 2,3,5,6,8 & 9 Not Used
10c
Not Used
10c
Not Used
10c
Not Used
10c
P19 Max DHW
Setpoint With b02 set to 1, 4 or 7
With b02 set to 2,3,5,6,8 & 9 Not Used
65c
Not Used
65c
Not Used
65c
Not Used
65c
P20 Max Output in
DHW Mode 0-100% 80% 80% 80% 80%
P21 Storage Cylinder
Hysteresis With b02 set to 1, 4 or 7
With b02 set to 2,3,5,6,8 & 9 Not Used
2c
Not Used
2c
Not Used
2c
Not Used
2c
P22 DHW Primary
Flow Temp With b02 set to 1, 4 or 7
With b02 set to 2,3,5,6,8 & 9 Not Used
80c
Not Used
80c
Not Used
80c
Not Used
80c
P23 Legionella
Protection With b02 set to 2,3,5,6,8 & 9
0 = Disabled ; 1 = Active 0 0 0 0
P24 Fan Freq in
Standby 0
– 255 Hz
0 Hz 0 Hz 0 Hz 0 Hz
P25 Modulating Pump
Control Temp 0
– 60c
35c 35c 35c 35c
P26 Primary Heat
Exchanger Dt
Protection 0
– 60c
35c 35c 35c 35c
P27 Min System PRV Not Used - - - -
P28 Rated Sys PRV Not Used - - - -
P29 Heat Exchanger
Protection
Activation 0 = No F43
1 = 1
– 15c / second
0 0 0 0
P30 Hysteresis in CH
mode start up 6
– 30c
10c 10c 10c 10c
P31 Hysteresis Timer
in CH mode start 60
– 180 Seconds
60 sec 60 sec 60 sec 60 sec