Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 278

Страница: 278 / 327

Service and maintenance of machine

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

278

8.15.3

Lubricate brake shaft bearing

Lubricate the outer and inner lubrication points
(3) of the brake shaft bearing with long-life
grease until fresh grease comes out of the
bearings.

Only use lithium-saponified grease with a drop
point above 190°C.

Make sure that no grease or oil
enters the brake system!

Depending on the series, the cam
bearing may not be sealed on the
brake side.

Fig. 146

Fig. 147

8.15.4

Lubricate standard slack adjuster

Lubricate the lubrication points (4) of the slack
adjuster with long-life grease until fresh grease
comes out.

Fig. 148

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды