USER MANUAL
CONTACT LIGHTING CONTROL PANEL
WWW. ST R A N D L I G H T I N G .CO M
11
RELAY INPUTS CONFIG
SUB MENU
OPTIONS
COMMENTS
Relay
N/A
Displays selected relay number if assigned.
DMX A
N/A
User de
fi
ned DMX address for DMX A port.
DMX B (Ethernet)
N/A
User de
fi
ned DMX address for DMX B port.
Room
N/A
Displays Relay’s assigned room number.
Channel
N/A
Displays Relay’s assigned channel number.
Flick Warn
IMPORTANT! Since some loads, such as
HID lamps, cannot be turned off and on
quickly, disabling Flick Warn (“No”) is
recommended for those relays.
N/A
Enables (selecting “Yes”) or Disables (selecting
“No”) to
fl
ick lights on and off (warning that a timed
event is about to occur to turn of the lights).
This time is programmed into the Sweep Off event
and is normally 5 minutes. Occupants can override
the sweep for up to 2 hours. This time is also
programmed into the event. The override is done by
pressing any button on a keypad.
Parked
Yes or No
Locally overrides all system control.
Trigger Level
1 to 255
Sets signal level for relay to trigger on and off.
DMX A Priority
None / Primary / Fallback
Sets priority level for DMX A (see note below)
DMX B Priority
None / Primary / Fallback
Sets priority level for DMX B (see note below)
Preset Priority
None / Primary / Fallback
Sets priority level for local presets
NOTE: DMX A and DMX B Priority Levels
There are three possible priority scenarios with two input sources:
• Primary vs. Primary - in the this case, the source with the highest level takes precedence (HTP).
• Primary vs. Fallback - in this case, the Primary source would take precedence -- unless the Primary source is not
present, at which time the Fallback source would take precedence.
• Fallback vs. Fallback - in the this case, the source with the highest level takes precedence (HTP), as long as a source
is actually present.
SYSTEM CONFIG
DMX A
Enabled / Disabled
Enables or disables the DMX A port to accept
DMX512 input signals.
DMX B
Ext Con
fi
g
Enables or disables the DMX B port to accept
DMX512 input signals. Only used when a DMX to
Ethernet node is installed.
Vision.net Network
Enabled / Disabled
Enables or disables the Vision.net Network port
Vision.net Station ID
Off / 1 thru 255
Sets Vision.net Station ID for the relay panel. If more
than one panel is connected to the same Vision.net
system, each panel should have a unique ID number.
DMX Hold (hh:mm) (in
hours:mins)
None / 0:01 / 0:05 / 0:10 /
0:15 / 1:00 /2:00 / 4:00 /
12:00 / 24:00 / Forever
Sets the amount of time the dimmer cabinet
will keep and hold the last DMX512 levels should
connection or signal be lost.
Power-up Preset
None / 1 / 2 / 3 / 4 / 5 / 6
/ 7 / 8
Sets what preset the dimmers go to when dimmer
cabinet is initially powered
Power-up Hold
Forever / 0:01 / 0:05 / 0:10
/ 0:15 / 1:00 / 2:00 / 4:00 /
12:00 / 24:00
Sets the amount of time the dimmers will go and
stay at the preset level (if set) when the dimmer
cabinet is initially powered.
Preset Clear
None / DMX A / DMX B /
DMX A/B / VN A / VN B /
VN A/B
Sets how local presets are cleared or overridden -
either never or via DMX512 or Vision.net commands
Con
fi
g Port
Ethernet / RS232
Sets con
fi
guration port to Ethernet or RS232 input.
Normal setting is Ethernet.
Panic Inputs
Normally Open / Normally
Closed
Sets panic inputs to open or closed. Note, for
UL924 applications, the panic input must be set to
Normally Open.
Continued on next page
