Stow MS-63 Скачать руководство пользователя | Manualshive

Страница: 23 / 128

background image

STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 23

This section is intended to assist the operator with
the initial start-up of the STOW MS-63H (gasoline
engine) or STOW MS-63E (electric motor) mixer. It
is extremely important that this section be read
carefully before attempting to use the mixer in the
field.

DO NOT

use your mixer until this section is thoroughly

understood.

Starting (gasoline only)

The following steps outline the procedure for starting the engine.
Depending on the type of engine employed in the mixer the
steps may vary slightly. If your mixer has an electric motor
disregard this section.

1.

Move the fuel shut-off lever (Figure 11) to the

ON

position.

Figure 11. Fuel Shut-OFF Lever

2.

To start a cold engine, move the choke lever (Figure 12) to
the

CLOSED

position.

Figure 12. Choke Lever

3.

Move the throttle lever (Figure 13) away from the slow
position, about 1/3 of the way toward the fast position.

Figure 13. Throttle Lever

STOW MS-63 PLASTER/MORTAR MIXER — START-UP PROCEDURES

Failure to understand the operation of the STOW MS-63
series mixers could result in

severe damage

to the mixer

or

personal injury

.

See Figures 5 and 6 for the location of any control
referenced in this manual.

WARNING

WARNING

WARNING

WARNING

WARNING

CAUTION

CAUTION

CAUTION

CAUTION

CAUTION

NEVER

operate the mixer in a confined

area or enclosed area structure that
does not provide ample

free flow of air

.

General Safety

Respiratory Hazard

«
...
21
22
23
24
25
...
»

Содержание MS-63

































































































































Отзывы:

Нет отзывов

Похожие инструкции для MS-63

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Datalogic Страницы: 188

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Hacker Страницы: 2

Бренд: Hadeco Страницы: 72

Tablet1000 Series

Бренд: Hantek Страницы: 98

Бренд: Carbatec Страницы: 29

Бренд: PurAthletics Страницы: 2

Бренд: LABORIE Страницы: 116

Fast Track Solo

Бренд: Avid Technology Страницы: 24

Nebula Blizzard v3

Бренд: Lanta Страницы: 8

Porta PlumeSafe 604

Бренд: Buffalo filter Страницы: 75

Shark Beam FX one

Бренд: SHOWTEC Страницы: 32

Бренд: STRIKEMASTER Страницы: 12

Бренд: natus Страницы: 42

Бренд: Xaoc Devices Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды