Stow MS-63 страница 17 Скачать руководство пользователя

Страница: 17 / 128

STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 17

STOW MS-63 PLASTER/MORTAR MIXER — BASIC ENGINE COMPONENTS

Figure 6. Engine Controls and Components

INITIAL SERVICING

The engine (Figure 6) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.

Fuel Filler Cap –

Remove this cap to add unleaded

gasoline to the fuel tank. Make sure cap is tightened
securely.

DO NOT

over fill.

Fuel Valve Lever –

OPEN

to let fuel flow,

CLOSE

to stop

the flow of fuel.

Choke Lever –

Used in the starting of a cold engine, or in

cold weather conditions. The choke enriches the fuel
mixture.

Air Cleaner –

Prevents dirt and other debris from entering

the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.

Operating the engine without an air
filter, with a damaged air filter, or a filter
in need of replacement will allow dirt

to enter the engine, causing rapid
engine wear.

Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity
to cool down. In the event of a fuel spill,

DO NOT

attempt to start the engine until the fuel residue
has been completely wiped up, and the area surrounding the
engine is dry.

DANGER

Throttle Lever –

Used to adjust engine RPM speed (lever

advanced forward

SLOW

, lever back toward operator

FAST

Engine ON/OFF Switch –

position permits engine

starting, OFF position stops engine operations.

Recoil Starter (pull rope) –

Manual-starting method. Pull

the starter grip until resistance is felt, then pull briskly and
smoothly.

Spark Plug –

Provides spark to the ignition system. Set

spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.

Muffler –

Used to reduce noise and emissions.

. Fuel Tank –

Holds unleaded gasoline. For additional

information refer to engine owner's manual.

NOTE

WARNING

Engine components can generate extreme heat.
To prevent burns,

DO NOT

touch these areas

while the engine is running or immediately after
operating.

NEVER

operate the engine with the

muffler removed.

Explosive

Fuel Hazard

Burn Hazard

Содержание MS-63

































































































































Результаты поиска

Содержание MS-63

Отзывы:

Похожие инструкции для MS-63

Бренды по названию

Популярные бренды

Stow MS-63, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MS-63

Отзывы:

Похожие инструкции для MS-63

Бренды по названию

Популярные бренды