Stow MS-63 страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 128

background image

PAGE 22 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)

STOW MS-63 PLASTER/MORTAR MIXER — INSPECTION

Fuel Check

V-belt Check

A worn or damaged V-belt can adversely affect the
performance of the mixer. If a V-belt is defective or worn
simply replace the V-belt as outlined in the maintenance
section of this manual.

Blade Check

Check for worn or paddle blades. Make sure that all blades
are adjusted properly. See blade adjustment procedure in
this manual. Replace all defective or damaged blades
immediately.

Controls

Start/Stop Switches

This mixer has been equipped with a start/stop switch for
both the gasoline and electric motor mixers. These switches
should be tested every time the engine or electric motor is
started.

Grease Fittings (Dumping Mechanism)

Check the zerk grease fittings at each end of the mixing
drum. These grease fittings lubricate the dumping
mechanism. If the dumping handle is stiff or hard to move
lubricate these fittings.

NEVER!

disable or disconnect the

start/stop switch

. It is

provided for operator safety. Injury may result if it is disable,
disconnected or improperly maintained.

CAUTION

CAUTION

CAUTION

CAUTION

CAUTION

1. Remove the gasoline cap located on top of fuel tank.

2. Visually inspect to see if fuel level is low. If fuel is low, replenish

with unleaded fuel.

3. When refueling, be sure to use a strainer for filtration.

DO

NOT

top-off fuel. Wipe up any spilled fuel.

DANGER

DANGER

DANGER

DANGER

DANGER

If your mixer has a gasoline engine, determine if the
engine fuel is low. If fuel is low, remove the fuel filler cap
and fill with

unleaded

gasoline. Motor

fuels are highly flammable and can be
dangerous if mishandled.

DO NOT

smoke

while refueling.

DO NOT

attempt to refuel

the mixer if the engine is

hot!

or

running

.

Explosive Fuel

Hazard

Start/Stop Switch

«
...
20
21
22
23
24
...
»

Содержание MS-63

































































































































Отзывы:

Нет отзывов

Похожие инструкции для MS-63

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 7

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 24

Бренд: Patlite Страницы: 28

Web Ankle Brace

Бренд: Darco Страницы: 2

Бренд: DARAY Страницы: 24

Body Armor Night Splint

Бренд: Darco Страницы: 2

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Hardt Страницы: 22

Бренд: Sabre Страницы: 2

Бренд: Parker Страницы: 24

Tychem ThermoPro TP198T

Бренд: Dupont Страницы: 42

Бренд: Brütsch Rüegger Страницы: 187

EXERCISE BALANCE PAD

Бренд: ProSource Страницы: 12

Бренд: 3M ESPE Страницы: 150

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды