Stow MS-63 страница 10 Скачать руководство пользователя | Manualshive

Страница: 10 / 128

background image

PAGE 10 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)

The following safety guidelines should always be used when
operating the STOW MS-63 mortar and plaster mixer:

GENERAL SAFETY

■

DO NOT

operate or service this

equipment before reading this entire
manual.

■

This equipment should not be operated by persons under
18 years of age.

■

NEVER

operate this equipment without proper protective

clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.

■

High Temperatures

– Allow the engine to cool before

adding fuel or performing service and maintenance
functions. Contact with

hot!

components can cause

serious burns.

■

The engine section of this mixer requires an adequate
free flow of cooling air.

NEVER

operate the mixer in any

enclosed or narrow area where
free flow of the air is restricted.
If the air flow is restricted it
will cause serious damage to
the mixer or engine and may
cause injury to people.
Remember the mixer's engine
gives off

DEADLY

carbon monoxide gas.

■

ALWAYS

refuel in a well-ventilated area, away from

sparks and open flames.

DANGER

DANGER

DANGER

DANGER

DANGER

Failure to follow instructions in this manual may lead
to serious injury or even death! This equipment is to
be operated by trained and qualified personnel only!
This equipment is for industrial use only.

■

NEVER

operate this equipment under the influence of

drugs

or

alcohol

.

Read this manual!

■

NEVER

touch the hot exhaust

manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or mixer.

■

ALWAYS

wear proper respiratory (mask),

hearing and eye protection equipment when
operating the mixer.

■

NEVER

place hands inside the drum while the blades

are rotating.

■

Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.

■

Manufacture does not assume responsibility for any
accident due to equipment modifications.

■

NEVER

use accessories or attachments, which are not

recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.

■

NEVER

operate this equipment when not

feeling well due to fatigue, illness or taking
medicine.

STOW MS-63 PLASTER/MORTAR MIXER — RULES FOR SAFE OPERATION

■

Topping-off to filler port is dangerous, as it tends to spill
fuel.

■

Stop the engine when leaving the mixer unattended.

■

Block the unit when leaving or when using on a slope.

■

Maintain this equipment in a safe operating condition at
all times.

■

NEVER

operate the mixer in an

explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe

bodily

harm or even death

.

NEVER

! start the engine or engage the paddle arms

when the drum is in the discharge (down) position.

WARNING

WARNING

WARNING

WARNING

WARNING

Starting the Mixer Engine

■

ALWAYS

use extreme caution when

working with

flammable

liquids. When

refueling,

stop the

engine and allow it to

cool.

DO NOT

smoke

around or near the

machine. Fire or explosion could result from
fuel vapors, or if fuel is spilled on a hot
engine.

«
...
8
9
10
11
12
...
»

Содержание MS-63

































































































































Отзывы:

Нет отзывов

Похожие инструкции для MS-63

Бренд: MAHLE Страницы: 21

Бренд: ParaBody Страницы: 4

Бренд: R.M. Young Страницы: 10

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

Бренд: U-Line Страницы: 9

Green Machine H-3518

Бренд: U-Line Страницы: 3

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

Бренд: Gaspardo Страницы: 44

MiniLift160 Classic

Бренд: Handicare Страницы: 28

Бренд: Hands Free Farm Страницы: 24

Бренд: i-Optik Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды