15
14
If the preceding tips do not
yield the desired results, or for
any other defects or problems
not mentioned here, please unplug
the power adapter and contact our
Service Center immediately.
Do not open the Vaporizer or
the power adapter! Without
special tools and specialized
knowledge, any attempt to open either
of these devices will cause damage to
them. Such an attempt will invalidate
the warranty claim.
6. THE
MIGHTY
VAPORIZER
Do not try to remedy the defect your-
self. Contact our Service Center di-
rectly.
Disposal
If the Vaporizer or the power adapter
is irreparably damaged, please do not
simply throw them away. As they are
made of high quality, completely recy-
clable component parts, they should
be brought to a material recycling
center in your town or sent to our Ser-
vice Center for disposal.
Possible Faults / Troubleshooting
Problem
Possible Cause/Remedy
MIGHTY
cannot be
switched on.
Please ensure that the
MIGHTY’s
battery is charged or
the Vaporizer is connected via the power adapter to a
functioning mains socket.
If the Vaporizer still does not work, then the device is
faulty. In this case, disconnect from the mains without
delay and get in touch immediately with our Service
Center.
The display of the
MIGHTY
shows: ERR 001.
Battery temperature is too high. Allow the Vaporizer to
cool down.
The display of the
MIGHTY
shows: ERR 002.
Battery temperature is too low. Warm up the Vaporizer.
The display of the
MIGHTY
shows: ERR 003.
The power adapter is not suitable. Please use an original
Storz & Bickel power adapter or 12 Volt car charger.
The display of the
MIGHTY
shows: ERR 004.
The Vaporizer is faulty. In this case, disconnect from the
mains without delay and get in touch immediately with
our Service Center.
7. COMMISSIONING AND OPERATION
Do not leave the device unat-
tended during operation.
Place the
MIGHTY
Vaporizer
only on a hard, heat-resistant, flat, sta-
ble surface, never on soft surfaces or
flammable material. Check whether
the power adapter supply voltage cor-
responds to the voltage rating listed
on the power adapter. The power
adapter cord and power adapter must
be in perfect condition. Connect the
power adapter only to a properly in-
stalled socket.
The manufacturer will not bear any
responsibility whatsoever if this acci-
dent prevention measure is not taken.
Please unplug the power adapter from
the mains socket to completely dis-
connect from the mains power supply.
7.1. Charging the Battery
Explanation of the battery charging
display:
The battery charging display shows
a battery symbol with six fields indi-
cating the charging status. If the bat-
tery is almost discharged, the battery
frame starts to flash; if fully charged,
the frame and all six fields are visible.
The number of status fields visible
depends on the extent of the battery
charge.
Battery charging display
Check the housings of the Va-
porizer and the power adapter
for signs of damage each time
before using or charing. The Vaporiz-
er may not be charged and neither
Vaporizer nor power adapter used if
these are damaged.
The battery charge of the new product
has a level of up to 80%. Fully charge
before using for the first time. The
charging time for the battery depends
on how old it is and how high the
charge is on starting; it takes about
two hours if the battery is completely
discharged.
Connect the power adapter to the
charging socket of the Vaporizer and
then plug into a suitable power socket.
Note: When the power adapter is
plugged into the mains, the display
lights up for a moment and the Vapor-
izer vibrates for a short time. This is
a functional check and indicates that
the charging operation has started.
The battery charging display lights up
and starts to flash, i.e. the battery is
being charged. As soon as the battery
is fully charged, the battery charging
display stops flashing and indicates
the charge level (full = all six fields).
Once the charging operation is com-
plete, first disconnect the power
adapter from the mains socket and
then unplug from the Vaporizer.
