STORK TRONIC 149674 страница 1 Скачать руководство пользователя | Manualshive

Страница: 1 / 11

background image

ST501-JX1TA

Temperature controller for fan drawers

Order number 900219.024

Old Id.Nr.: 149674

Wiring diagram

Product description

The ST501-JX1TA controller comprises a control unit and a power supply unit board. Both com-
ponents are interconnected via a ribbon cable and form a plug-in unit. All input and output connec-
tions are established in the rear on the power supply unit board. The unit provides the functionality
of a temperature controller for fan drawers.
A triac for fan control and a relay are provided as outputs. The relay is a normally open contact and
can be defined either as control circuit 2 or as an alarm contact using the parameter setting function.

Sensor: PTC, Pt100
Range: dependent on type of sensor
Front dimensions: 106mm x 68mm
Panel cutout: 87.5mm x 56.5mm
Tightness: Front IP65
Connection: screw terminals
Versorgung: 230V AC

1

1
2
3
...
»

Содержание 149674












Отзывы:

Нет отзывов

Похожие инструкции для 149674

Бренд: Magnescale Страницы: 132

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: PAC Страницы: 17

Бренд: HABONIM Страницы: 9

Бренд: MAKOT Страницы: 6

Бренд: Parkside Страницы: 65

TEMP2000 Series

Бренд: Samwontech Страницы: 91

Бренд: Warren rupp Страницы: 18

Бренд: Yamaha Страницы: 100

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

Бренд: Vizio Страницы: 65

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: YASKAWA Страницы: 340

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды