STORK TRONIC 149674 страница 11 Скачать руководство пользователя

Страница: 11 / 11

Order number: 149674

Technical data of ST501-JX1TA

Input

F1:

resistance thermometer

Range:

PTC (KTY81-121)

-50 °C ... +130 °C

PT1000

-99 °C ... +300 °C

Pt100

-80 °C ... +400 °C

Accuracy:

±0.5K ± 0.5 % at 25 °C, without sensor

±1K ± 0.5 % across entire temperature range (0 – +55 °C), without sensor

Outputs

K1:

relay, 16(2.2)A 250V NO contact
(limited to 10(2.2)A through terminals or printed circuit board)

triac output for fan

Additional buzzer, 85 dB

Display and indicators

One 3-digit LED display for temperature indication
Three LEDs for status indication

Power supply

230 V, 50/60 Hz

Connectors

12-pin screw terminal, 5.0 mm pitch, for cable cross sections of up to 2.5 mm²

Weight

Approx. 250 g, without sensor.

Type of protection

Front IP65

Ambient conditions

Storage temperature:

-20 °C ... +70 °C

Operating temperature:

0 ... 55 °C

Relative humidity:

max. 75%, non-condensing

Installation data

Front dimensions: 106 x 68 mm
Panel cutout:

87.5 x 56.5 mm

Installation depth: approx. 50 mm

Содержание 149674












Результаты поиска

Содержание 149674

Отзывы:

Похожие инструкции для 149674

Бренды по названию

Популярные бренды

STORK TRONIC 149674, Руководство пользователя

Результаты поиска

Содержание 149674

Отзывы:

Похожие инструкции для 149674

Бренды по названию

Популярные бренды