background image

866-795-1586 • WWW.STONEAGETOOLS.COM

33

9. 

Governing Law.

  All sales, agreements for sale, offers to sell, 

proposals, acknowledgments and contracts of sale, including, 
but not limited to, purchase orders accepted by Seller, shall be 
considered a contract under the laws of the State of Colorado 
and the rights and duties of all persons, and the construction 
and effect of all provisions hereof shall be governed by and 
construed according to the laws of such state.

10. 

Jurisdiction and Venue. 

 Seller and Buyer agree that the 

state or federal courts located within the City and County of 
Denver, Colorado shall have sole and exclusive jurisdiction over 
any litigation concerning any dispute arising under these Terms 
and Conditions not otherwise resolved pursuant to Section  9 
as well as any alleged defects of any Products  or damages 
sustained as a result of such alleged defects.  Seller and 
Buyer further agree that should any litigation be commenced 
in connection with such a dispute, it shall only be commenced 
in such courts.  Seller and Buyer agree to the exclusive 
jurisdiction of such courts and neither will raise any objection to 
the jurisdiction and venue of such courts, including as a result 
of inconvenience. 

11. 

Attorney’s Fees.

  If any litigation is commenced between 

Seller and Buyer, or their personal representatives, concerning 

any provision hereof, the party prevailing in the litigation shall 

be entitled, in addition to such other relief that is granted, to a 
reasonable sum as and for their attorneys’ fees and costs in 
such litigation or mediation.

STONEAGE TRADEMARK LIST  
View the list of StoneAge’s trademarks and service marks and learn how the trademarks should be used. Use of StoneAge 
trademarks may be prohibited, unless expressly authorized. 

http://www.StoneAgetools.com/trademark-list/ 

STONEAGE PATENT DATA  
View the list of StoneAge’s current U.S. patent numbers and descriptions.

http://www.sapatents.com

STONEAGE TERMS AND WARRANTY 
View StoneAge’s Terms and Warranty Conditions online.

http://www.stoneagetools.com/terms
http://www.stoneagetools.com/warranty

TERMS AND CONDITIONS AND WARRANTY INFORMATION

Содержание BADGER BA-H6





































Отзывы: