manualshive.com logo in svg

StoneAge AUTOSTROKE AST-200-V2, Руководство пользователя

Поделиться
Скачать
StoneAge AUTOSTROKE AST-200-V2 Скачать руководство пользователя страница 6

6

866-795-1586 • WWW.STONEAGETOOLS.COM

PERSONAL PROTECTIVE EQUIPMENT REQUIREMENTS

Use of Personal Protective Equipment (PPE) is dependent on 
the working pressure of water and the cleaning application. 
Managers, Supervisors, and Operators MUST carry out a job 
specific risk assessment to define the exact requirements for 
PPE. See Protective Equipment for Personnel (Section 6) of 
WJTA-IMCA’s Recommended Practices For The Use Of High-
pressure Waterjetting Equipment for additional information.
Hygiene - Operators are advised to wash thoroughly after all 
waterjetting operations to remove any waterblast residue which 
may contain traces of harmful substances.
First aid provision - users MUST be provided with suitable first 
aid facilities at the operation site.

PPE may include:

•  Eye protection:

 Full face visor

•  Foot protection:

 Kevlar

® 

brand or steel toe capped, 

waterproof, non-slip safety boots

•  Hand protection:

 Waterproof gloves

•  Ear protection:

 Ear protection for a minimum of 85 dBA

•  Head protection: 

Hard hat that accepts a full face visor 

and ear protection

•  Body protection:

 Multi-layer waterproof clothing approved 

for waterjetting

•  Hose protection: 

Hose shroud

•  Respiratory protection: 

May be required; refer to job 

specific risk assessment

OPERATOR TRAINING

Managers, Supervisors, and Operators MUST be trained in Health 
and Safety Awareness of High-pressure Water Jetting and hold 
a copy the Water Jetting Association (WJA) Code of Practice, or 
equivalent (see 

www.waterjetting.org.uk

).

Operators MUST be trained to identify and understand all applicable 
standards for the equipment supplied. Operators should be trained 

in manual handling techniques to prevent bodily injury.

Operators MUST read, understand, and follow the Operational and 

Training Requirements (Section 7.0) of WJTA-IMCA’s Recommended 

Practices For The Use Of High-pressure Waterjetting Equipment, or 
equivalent.
Operators MUST read, understand and follow the Warnings, 
Safety Information, Assembly, Installation, Connection, Operation, 

Transport, Handling, Storage, and Maintenance Instructions detailed 

in this manual.

StoneAge has designed and manufactured this equipment 
considering all hazards associated with its operation. StoneAge 
assessed these risks and incorporated safety features in the design. 
StoneAge 

WILL NOT

 accept responsibility for the results of misuse.

IT IS THE RESPONSIBILITY OF THE INSTALLER/OPERATOR

 

to conduct a job specific risk assessment prior to use. Job specific 
risk assessment MUST be repeated for each different set up, 
material, and location. 
The risk assessment MUST conform to the Health and Safety at 
Work Act 1974 and other relevant Health and Safety legislation. 

The risk assessment MUST consider potential material or substance 
hazards including:

•  

Aerosols 

•  

Biological and microbiological (viral or bacterial) agents

•  

Combustible materials 

•  

Dusts 

•  

Explosion 

•  

Fibers 

•  

Flammable substances

•  

Fluids

•  

Fumes

•  

Gases

•  

Mists

•  

Oxidizing Agents

WARNING AND SAFETY INSTRUCTIONS

Содержание AUTOSTROKE AST-200-V2





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды