manualshive.com logo in svg

StoneAge AUTOSTROKE AST-200-V2, Руководство пользователя

Поделиться
Скачать
StoneAge AUTOSTROKE AST-200-V2 Скачать руководство пользователя страница 18

18

866-795-1586 • WWW.STONEAGETOOLS.COM

The AutoStroke™ (AST-200-V2) should be stored in a dry location between jobs. Before storing the unit, use compressed air to blow out 
any debris and moisture. Use mild soapy water to clean the machine in order to remove corrosive materials.  Apply a small amount of air 
tool oil directly into the forward and reverse fittings. Install the dust caps onto all fittings to keep moisture and dirt out.

STORAGE, TRANSPORTATION, AND HANDLING

Contact StoneAge for Safety Data Sheets for material usage and any other pertinent information that may be required.

MAINTENANCE

Maintenance Item

Frequency

Maintenance Required

Air Motor Generator Replacement

When Needed

If the Air Motor Generator fails on the AutoStroke, it is possible to replace 
it.  Please call  your StoneAge Customer Service Representative to order 
part number 

AMG-100-V2 AIR MOTOR GENERATOR, WITH FITTINGS.         

Follow the Air Motor Generator Replacement instructions located in this 
manual

All Air Fittings

After 

each use

Reinstall all dust caps to protect from dirt and moisture.

Air Lines

Before 

each use

Blow out before making connections to the AutoStroke

Electrical Connections

Frequently

Visually inspect for corrosion.

MAINTENANCE

NOTICE

Electronic components are not user serviceable. If troubleshooting the system fails it must be sent back to StoneAge Tools for service.  

Contact your customer service representative. 1-866-795-1586

Problem

Solution

AST-200 is not functioning

-Check that airlines are connected properly
-Check that switch is on and red LED is lit while feeding forward
-Increase sensitivity
-Verify that fuse is not blown

AST-200 continues to reverse feed

-Check that hose is not getting hung up behind the ABX
-Reduce sensitivity
-Reduce hose drag

AST-200 power light is not coming on but the 

switch is in the “

ON”

 positon

- 

Toggle rhe AutoStroke to the

 “OFF”

 Position, run the Autobox Tractor in Reverse until the 

Air Motor Generator goes silent. This may take up to one minute and will allow the Air Motor 
Generator to charge. The charge time could be longer with lower pressures.

TROUBLESHOOTING

Содержание AUTOSTROKE AST-200-V2





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды