StoneAge AUTOSTROKE AST-200-V2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

background image

21

866-795-1586 • WWW.STONEAGETOOLS.COM

AIR MOTOR GENERATOR REPLACEMENT

AIR MOTOR GENERATOR INSTALLATION INSTRUCTIONS.....CONTINUED

Correct Air Motor Generator location inside the
AST-200-V2 AUTOSTROKE

4. Connect the 2 air tubes from the air motor generator.

5. Close the AutoStroke lid with a flat screwdriver. Turn the

quarter turn latches clockwise 90 degrees and tighten the
cover onto the AutoStroke.

«
...
19
20
21
22
23
...
»

Содержание AUTOSTROKE AST-200-V2





























Отзывы:

Нет отзывов

Похожие инструкции для AUTOSTROKE AST-200-V2

Бренд: FeiYu Tech Страницы: 6

Бренд: Faudi Страницы: 18

Бренд: Varta Страницы: 2

Бренд: YUNEEC Страницы: 6

Бренд: Vortice Страницы: 132

Бренд: Allen Sports Страницы: 2

Fireplace Surrounds None

Бренд: Dimplex Страницы: 2

Бренд: Gira Страницы: 10

Бренд: AOR Страницы: 29

Бренд: EVA Logik Страницы: 2

Бренд: Stack Страницы: 2

Бренд: Videotec Страницы: 16

Бренд: DYNATEK Страницы: 4

Бренд: Gira Страницы: 4

Бренд: Kabuto Страницы: 28

STEADYSTAND Cross Basic

Бренд: ACEBIKES Страницы: 6

Бренд: RADARchron Страницы: 2

Бренд: Ednet Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды