background image

 

 

DOMESTIC WARRANTY 

 

 

(Including Mexico) 

 
 
 

Page 1 of 2 

SFWARR-013 Revision 10 

1. 

Scope

 

Stoelting, A Vollrath Company (“Stoelting”) warrants to the first user (the “Buyer”) that the Stoelting-branded freezer 
equipment (the “Equipment”) will be free from defects in materials and workmanship under normal use and proper 
maintenance for the period listed below in the Warranty Period section. All warranty periods begin on the date of original 
install or one (1) year from the shipping date, whichever occurs first. This warranty is subject to all conditions, 
exceptions, and limitations contained herein. 

 
2. 

Disclaimer of Other Warranties

 
 

THIS WARRANTY IS EXCLUSIVE; AND STOELTING HEREBY DISCLAIMS ANY IMPLIED WARRANTY 
OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. 

 
3. 

Remedies

 

Stoelting’s sole obligations, and Buyer’s sole remedies, for any breach of this warranty shall be, at Stoelting’s option, 
one of the following: repair or replacement of the affected component at Stoelting’s plant in Kiel, Wisconsin, or refund 
of the purchase price of the affected Equipment. Stoelting, through an Authorized Stoelting Provider, will 
deinstall/reinstall the affected component from/into the equipment (“Labor”) for the period listed below in the Warranty 
Period section. These obligations/remedies are subject to the conditions that Buyer (a) signs and returns to Stoelting, 
upon installation, the Start-Up and Training Checklist for the affected equipment, (b) gives Stoelting prompt written 
notice of any claimed breach of warranty within the applicable warranty period, and (c) delivers the affected equipment 
to Stoelting or its designated service location, in its original packaging/crating, also within that period. Buyer shall bear 
the cost and risk of shipping to and from Stoelting’s plant or designated service location. 

 
4. 

Warranty Period: 

 

Equipment

Part

Part Warranty Period

Labor Warranty Period

Freezing Cylinders
Hoppers
Compressors
Drive Motors
Speed Reducers
Augers
Evaporator
Compressors
Drive Motors
Speed Reducers
Freezing Cylinders
Hoppers
Compressors
Drive Motors
Speed Reducers
Beaters
Auger Shafts

Dipping Cabinets & 

Display Cabinets

All components

Twelve (12) Months

Twelve (12) Months

Compressors

Five (5) Years

Electronic Board

Three (3) Years

All other components

Two (2) Years

AutoVend

All components

Twelve (12) Months

Twelve (12) Months

Compressors
Motors
Condensers

All equipment

All other components 
not specified above

Twelve (12) Months

Twelve (12) Months

Custard & Batch

Two (2) Years

Twelve (12) Months

Soft Serve & Shake

Five (5) Years

Twelve (12) Months

Frozen Uncarbonated 

Beverage

Five (5) Years

Twelve (12) Months

Crème Whippers

Two (2) Years

Twelve (12) Months

Frozen Beverage / 

Granita Dispenser

Twelve (12) Months

 

Содержание SO212































Отзывы: