Stoelting E111I, Руководство оператора

Страница: 18 / 35

Owner’s Manual #513532-5 Rev.1 12 E111I/F111I Model Machines
8. Press the SET button. A cursor will start blinking
under the far right digit.
9. Change the value to 8.0. Press the left arrow (

)
button to move the cursor. Press the up arrow (

)
button to increase the digit. When a digit reaches
9, pressing the up arrow (

) button again will
change the value to 0.
10. After entering 8.0, press SET to save this value.
The LCD will read “CutOut Set -- OK”.
11. Press the SEL button. The LCD will read “CutOut
amps 8.0”.
12. Press the SEL button twice. The LCD will read
“DISPLAY”.
13. Press the up arrow (

) button to navigate to the
“°F” and “amps” readings.
C. INITIAL FREEZE DOWN
14. Place the Main Freezer Power OFF-ON switch
in the ON position.
15. Press the PUSH TO FREEZE button.
NOTE
After the drive motor starts, there is a 3-second
delay before the compressor starts.
16. As the product freezes, the “amps” value on the
display will increase. When it reaches 2.8A, open
the spigot, take a 6-8 ounce sample and measure
the temperature. For most soft serve mixes,
the desired temperature is between 19.0°F and
19.5°F.
17. Draw samples at every increase of 0.2A until
reaching the desired consistency and temperature.
NOTE
Show the sample to the customer and make sure it
meets their required consistency and temperature.
18. Record the “amps” value.
19. Place the Main Freezer Power OFF-ON switch
in the OFF position.
D. ADJUSTING THE INTELLITEC CONTROL
20. Press the SEL button. The display will read
“DISPLAY”.
21. Press the left arrow (

) button once. The display
will read “BASIC”.
22. Press the up arrow (

) button once. The display
will read “CutOut amps”.
23. Change the value to the recorded value by
pressing the SET button. A cursor will start blinking
under the far right digit.
24. Press the left arrow (

) button to move the cursor.
Press the up arrow (

) button to increase the digit.
When a digit reaches 9, pressing the up arrow
(

) button again will change the value to 0.
25. Press the SET button to save the value. The LCD
will read “CutOut Set -- OK”.
26. Press the SEL button. The LCD will read “CutOut
amps” along with the programmed value from the
previous step.
27. Press the SEL button three times. The LCD will
read “EXITMENU”.
28. Press the up arrow (

) button to exit the menu.
29. Adjustment to the control is completed.
E. SERVING PRODUCT
30. Place the Main Freezer Power OFF-ON switch
in the ON position.
31. Press the PUSH TO FREEZE button.
32. When the product is at 75% consistency, the
display will read “SERVE”.
33. For normal dispensing, move the spigot handle
fully open.
34. The machine dispenses product at a reasonable
draw rate. If the machine is overdrawn, the result
is a soft product or a product that will not dispense
at all. If this occurs, allow the machine to run for
approximately 30 seconds before dispensing more
product. A dispense rate adjustor is located under
the header panel, to the immediate right of the
spigot handle. Turning the knob counterclockwise
will decrease the dispense rate.
35. Do not operate the machine when the MIX LOW
message is displayed. Refi ll the mix container
immediately.
NOTE
The machine has a standby and sleep mode. After
a preset number of freezing cycles, it will enter the
standby mode (followed by sleep mode) and remain
there until someone draws product or presses the
PUSH TO FREEZE button. In the sleep mode, the
machine will keep the product below 41°F (4.4°C).
Sleep modes do not take the place of cleaning
and sanitizing. Federal, State, and local regulatory
agencies determine frequency of cleaning and
sanitizing.
3.11 NORMAL FREEZE DOWN AND
OPERATION
The following section contains the recommended oper-
ating procedures for the safe operation of the machine.
A. Sanitize immediately before use.
B. Make sure the Main Freezer Power OFF-ON
switch is in the OFF position.
C. Fill the hopper with at least 2.5 gallons of mix.
D. Place a container under the spigot and open the
spigot to allow the mix to fl ush out about 8 ounces
(0.23 liters) of sanitizing solution and liquid mix.