manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

BS_General purpose timers

RM0082

320/844

Doc ID 018672 Rev 1

         

17.2.2 Register 

map

Programming a set of 16 bit wide registers can configure each GPT. The registers of the 
three GPTs are mapped in memory by couples, namely:

●

The local timer in the CPU subsystems, which can be accessed at the base address 
0xF000_0000.

●

The two timers in the basic subsystem, which can be accessed at the base addresses 
0xFC80_0000 and 0xFCB0_0000.

The registers are same for both the couples of GPTs and are listed in 

Table 255

. 

Section 17.2.3

 describes the registers of a generic GPT.

Table 254.

GPT interface signal description

Pin Name

Type

Source/Destination

Description

CLK

In

Clock root

APB system (bus) clock. This clock 
times all the bus transfers.

Synchronous logic inside the GPT id 
rising edge clock triggered.

RESETn

In

Reset block

Synchronous reset of the GPT, all 
internal registers are cleared when this 
input is driven low.

PADDR[8:2]

In

APB Bridge

Standard APB address bus.

PSEL

In

APB Bridge

Standard APB psel signal.

PENABLE

In

APB Bridge

Standard APB penable signal.

PWRITE

In

APB Bridge

Standard APB write signal.

PRDATA [15:0]

Out

APB Bridge

Standard APB prdata signal.

PWDATA[15:0]

In

APB Bridge

Standard APB pwdata signal.

TIMER_CLK

In

Clock root

Timer clock (Refer to Bit 11 & 12 in 

Table 218: SSPIMSC register bit 
assignments

).

TMR_CPAT1

In

External Pin

Asynchronous signal provided for the 
measurement of timing signals in 
Timer1.

TMR_CAPT2

In

External Pin

Asynchronous signal provided for the 
measurement of timing signals in 
Timer2.

MT_INT1

Out

Interrupt Controller

Active low interrupt to Interrupt Control 
block from Timer1.

TMR_CLK

Out

Interrupt Controller

Clock which toggles each time the 
MT_INT1 goes active.

MT_INT2

Out

Interrupt Controller

Active low Interrupt to Interrupt Control 
block from Timer2.

TMR_CLK

Out

Interrupt Controller

Clock which toggles each time the 
MT_INT2 goes active.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Бренд: ABB Страницы: 17
Rabbit microBLUE Instruction Manual preview
microBLUE
Бренд: Rabbit Страницы: 12
vanEE VENMAR ADVANCED TOUCHSCREEN CONTROL Installation And User Manual preview
VENMAR ADVANCED TOUCHSCREEN CONTROL
Бренд: vanEE Страницы: 4
GOAL ZERO 10 AMP User Manual preview
10 AMP
Бренд: GOAL ZERO Страницы: 52
MIT TRG-BS-12 User Manual preview
TRG-BS-12
Бренд: MIT Страницы: 20
CLS LDV-45 Manual preview
LDV-45
Бренд: CLS Страницы: 6
Dräger REGARD-1 Installation, Operation And Maintenance Manual preview
REGARD-1
Бренд: Dräger Страницы: 48
Sierra Wireless AirPrime MC7350 Hardware Integration Manual preview
AirPrime MC7350
Бренд: Sierra Wireless Страницы: 20
Thermal Solutions Boiler Control TSBC Instruction Manual preview
Boiler Control TSBC
Бренд: Thermal Solutions Страницы: 48
mikroElektronika BIGdsPIC6 User Manual preview
BIGdsPIC6
Бренд: mikroElektronika Страницы: 28
Eaton Smart Home Controller 2.0 Quick Installation Manual preview
Smart Home Controller 2.0
Бренд: Eaton Страницы: 24
DYNACO DYNALOGIX II DY 4000 Electrical Manual preview
DYNALOGIX II DY 4000
Бренд: DYNACO Страницы: 13
Gira 0425 00 Quick Start Manual preview
0425 00
Бренд: Gira Страницы: 7
TA SMS14U Manual preview
SMS14U
Бренд: TA Страницы: 4
Heinzmann HELENOS V DC 2005DP.2-01 Manual preview
HELENOS V DC 2005DP.2-01
Бренд: Heinzmann Страницы: 66
National Instruments cRIO-9030 Getting Started Manual preview
cRIO-9030
Бренд: National Instruments Страницы: 18
TrailMaster BLE-PRO User Manual preview
BLE-PRO
Бренд: TrailMaster Страницы: 2
Dontek V2-1 Quick Start Manual preview
V2-1
Бренд: Dontek Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды