manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

LS_Synchronous serial peripheral (SSP)

Doc ID 018672 Rev 1

281/844

         

13.6.9 SSPIMSC 

register

The SSPIMSC register is the interrupt mask set or clear register. It is a read/write register. 
On a read this register gives the current value of the mask on the relevant interrupt. A write 
of 1 to the particular bit sets the mask, enabling the interrupt to be read. A write of 0 clears 
the corresponding mask. All the bits are cleared to 0 when reset. The SSPIMSC bit 
assignments are given in 

Table 218

.

         

13.6.10 SSPRIS 

register

The SSPRIS register is the raw interrupt status register. It is a read-only register. On a read 
this register gives the current raw status value of the corresponding interrupt prior to 
masking. A write has no effect. The SSPRIS bit assignments are given in 

Table 219

.

         

Table 217.

SSPCPSR register bit assignments

Bit

Name

Type

Description

[15:08] -

-

Reserved, read unpredictable, must be written as 0.

[07:00] CPSDVSR

R/W

Clock prescale divisor. Must be an even number from 2 to 254, 
depending on the frequency of SSPCLK. The least significant bit 
always returns zero on reads.

Table 218.

SSPIMSC register bit assignments

Bit

Name

Type

Description

[15:04]

-

-

Reserved, read as 0, do not modify.

[03]

TXIM

R/W

Transmit FIFO interrupt mask:

1’b0 = Tx FIFO half empty or less condition interrupt is masked.

1’b1 = Tx FIFO half empty or less condition interrupt is not masked

[02]

RXIM

R/W

Receive FIFO interrupt mask:

1’b0 = Rx FIFO half full or less condition interrupt is masked

1’b1 = Rx FIFO half full or less condition interrupt is not masked.

[01]

RTIM

R/W

Receive timeout interrupt mask:

1’b0 = Rx FIFO not empty and no read prior to timeout period interrupt is 
masked

1’b1= Rx FIFO not empty and no read prior to timeout period interrupt is 
not masked.

[00]

RORI
M

R/W

Receive overrun interrupt mask:

1’b0 = Rx FIFO written to while full condition interrupt is masked

1’b1= Rx FIFO written to while full condition interrupt is not masked.

Table 219.

SSPRIS register bit assignments

Bit

Name

Type

Description

[15:04] -

-

Reserved, read as 0, do not modify.

[03]

TXRIS

RO

Gives the raw interrupt state (prior to masking) of the SSPTXINTR 
interrupt

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Eastern Times Technology BT-100 Quick Start Manual preview
BT-100
Бренд: Eastern Times Technology Страницы: 4
Vacon 10 Quick Manual preview
10
Бренд: Vacon Страницы: 18
Zener SMARTSTART 6000 Networking Manual preview
SMARTSTART 6000
Бренд: Zener Страницы: 36
Zapi SMART CONSOLE Instructions preview
SMART CONSOLE
Бренд: Zapi Страницы: 5
Interlogix TruPortal TP-ADD-1DIP Quick Reference preview
TruPortal TP-ADD-1DIP
Бренд: Interlogix Страницы: 9
YASKAWA PG-X2 Instructions Manual preview
PG-X2
Бренд: YASKAWA Страницы: 12
MAKOT UMS-04 Series Manual preview
UMS-04 Series
Бренд: MAKOT Страницы: 6
NXP Semiconductors LPC2880 User Manual preview
LPC2880
Бренд: NXP Semiconductors Страницы: 362
On-Q lyriQ AU7394 Series Instruction/Installation Sheet preview
lyriQ AU7394 Series
Бренд: On-Q Страницы: 8
i4Home Smart Box Eco Quick Installation Manual preview
Smart Box Eco
Бренд: i4Home Страницы: 2
S&P CONTROL ECOWATT Manual preview
CONTROL ECOWATT
Бренд: S&P Страницы: 32
SHOWTEC 70237 Manual preview
70237
Бренд: SHOWTEC Страницы: 20
AMD Am7990 Reference Manual preview
Am7990
Бренд: AMD Страницы: 12
Canford TECPRO HS581 Manual preview
TECPRO HS581
Бренд: Canford Страницы: 2
Napoleon eFIRE Operating Instructions Manual preview
eFIRE
Бренд: Napoleon Страницы: 8
Overland Storage NEO Agility 48 10GbE Card Instructions preview
NEO Agility 48 10GbE Card
Бренд: Overland Storage Страницы: 4
PICO Solareg PICO 200 Operating Manual preview
Solareg PICO 200
Бренд: PICO Страницы: 12
HomeMatic HmIP-FAL24-C6 Installation Instructions And Operating Manual preview
HmIP-FAL24-C6
Бренд: HomeMatic Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды