Stihl MS440 Скачать руководство пользователя страница 49

Страница: 49 / 52

MS 440

English

Engine

STIHL single cylinder two-stroke engine

Ignition System

Electronic magneto ignition

Fuel System

All position diaphragm carburetor with

integral fuel pump

Chain Lubrication

Fully automatic, speed-controlled

reciprocating oil pump. Manual oil flow

control

Weight

Cutting Attachment

Actual cutting length may be less than

the specified length

Rollomatic guide bars

3/8" chains

Chain sprockets

As a rule, the mean chain velocity in

operation is about 20% lower than the

maximum chain velocity in accordance

with ISO 11681. Contact your STIHL

servicing dealer for advice on personal

protective equipment.

Noise and Vibration Data

For further details on compliance with

Vibration Directive 2002/44/EC see

www.stihl.com/vib.

Sound pressure level L

peq

to ISO 22868

Sound power level L

to ISO 22868

Vibration measurement a

hv,eq

ISO 22867

The K

factor in accordance with

Directive 2006/42/EC is 2.5 dB(A) for

the sound pressure level and sound

power level; the K

factor in accordance

with Directive 2006/42/EC is 2.0 m/s

for the vibration measurement.

REACH

REACH is an EC regulation and stands

for the Registration, Evaluation,

Authorisation and Restriction of

Chemical substances.
For information on compliance with the

REACH regulation (EC) No. 1907/2006

see www.stihl.com/reach.

Specifications

Displacement:

70.7 cc

Bore:

50 mm

Stroke:

36 mm

Engine power to

ISO 7293:

4.0 kW (5.4 HP)

at 9,500 rpm

Idle speed:

to ISO 11681 +/- 50 rpm

2,500 rpm

Spark plug (resistor

type):

Bosch WSR 6 F,

NGK BPMR 7 A

Electrode gap:

0.5 mm

Fuel tank capacity:

780 cc (0.78 l)

Oil tank capacity:

275 cc (0.275 l)

dry, without bar and chain
MS 440:

6.3 kg

MS 440 with handle heating:

6.5 kg

Cutting lengths:

37, 40, 45, 50,

63, 75 cm

Pitch:

3/8"

Groove width:

1.6 mm

Rapid Micro (36 RM) Type 3652
Rapid Super (36 RS) Type 3621
Rapid Super 3 (36 RS3) Type 3626
Pitch:

3/8" (9.32 mm)

Drive link gauge:

1.6 mm

7-tooth for 3/8" (rim sprocket)
Max. chain velocity to

ISO 11681:

27.5 m/s

7-tooth for 3/8" (spur sprocket)
Max. chain velocity to

ISO 11681:

27.5 m/s

101 dB(A)

116 dB(A)

Handle, left

4.2 m/s

Handle, right:

4.5 m/s

Содержание MS440





















































Результаты поиска

Содержание MS440

Отзывы:

Похожие инструкции для MS440

Бренды по названию

Популярные бренды

Stihl MS440, Инструкция по эксплуатации

Результаты поиска

Содержание MS440

Отзывы:

Похожие инструкции для MS440

Бренды по названию

Популярные бренды