Stihl MS 461 Rescue Скачать руководство пользователя

Страница: 38 / 52

MS 461

English

If the engine is down on power,

difficult to start or runs poorly at idle

speed, first check the spark plug.

Fit a new spark plug after about 100

operating hours – or sooner if the

electrodes are badly eroded. Install

only suppressed spark plugs of the

type approved by STIHL – see

"Specifications".

Removing the spark plug

Turn the knob above the rear handle

in the direction of the arrow and

remove the carburetor box cover

Lift the air baffle (1) up and off

Unplug spark plug boot (2)

Unscrew spark plug

Checking the Spark Plug

Clean dirty spark plug.

Check electrode gap (A) and

readjust if necessary – see

"Specifications".

Rectify the problems which have

caused fouling of the spark plug.

Possible causes are:

–

Too much oil in fuel mix.

–

Dirty air filter.

–

Unfavorable running conditions.

WARNING

Arcing may occur if the adapter nut (1) is

loose or missing. Working in an easily

combustible or explosive atmosphere

may cause a fire or an explosion. This

can result result in serious injuries or

damage to property.

Use resistor type spark plugs with a

properly tightened adapter nut.

Installing the spark plug

Screw in the spark plug

Press on the spark plug boot (1)

firmly

Insert the air baffle (2) from above

Mount carburetor box cover

Spark Plug

145BA027 K

145BA039 KN

000BA039 KN

000BA045 KN

3443BA01

1 KN

Содержание MS 461 Rescue





















































Результаты поиска

Содержание MS 461 Rescue

Отзывы:

Похожие инструкции для MS 461 Rescue

Бренды по названию

Популярные бренды

Stihl MS 461 Rescue, Инструкция по эксплуатации

Результаты поиска

Содержание MS 461 Rescue

Отзывы:

Похожие инструкции для MS 461 Rescue

Бренды по названию

Популярные бренды