Stihl MS 461 Rescue Скачать руководство пользователя

Страница: 26 / 52

MS 461

English

Preparing the machine

Thoroughly clean the oil filler cap

and the area around it to ensure that

no dirt falls into the oil tank.

Always position the machine so that

the filler cap is facing upwards.

Open the filler cap.

Filling the chain oil tank

Standard oil pump

Fill the chain oil tank each time the

fuel tank has been filled

Oil pump with increased delivery rate

(available option)
It is necessary to check and refill the oil

tank frequently – see "Adjusting the oil

quantity".

Refill the oil tank when the fuel tank

is approximately half empty

All versions
Take care not to spill chain oil while

refilling and do not overfill the tank.
STIHL recommends use of the STIHL

filling system for chain oil (available

option).

Close the filler cap

There must still be a small amount of oil

in the oil tank when the fuel tank is

empty.
If the oil tank is still partly full, the reason

may be a problem in the oil supply

system: Check chain lubrication, clean

the oil passages, contact a servicing

dealer if necessary. STIHL recommends

that maintenance and repair work be

carried out only by authorized STIHL

dealers.

The saw chain must always throw off a

small amount of oil.

NOTICE

Never operate your saw without chain

lubrication. If the chain runs dry, the

whole cutting attachment will be

irretrievably damaged within a very short

time. Always check chain lubrication and

the oil level in the tank before starting

work.
Every new chain has to be broken in for

about 2 to 3 minutes.
After breaking in the chain, check chain

tension and adjust if necessary – see

"Checking Chain Tension".

Filling Chain Oil Tank

001BA158 KN

Checking Chain Lubrication

143BA024 KN

Содержание MS 461 Rescue





















































Результаты поиска

Содержание MS 461 Rescue

Отзывы:

Похожие инструкции для MS 461 Rescue

Бренды по названию

Популярные бренды

Stihl MS 461 Rescue, Инструкция по эксплуатации

Результаты поиска

Содержание MS 461 Rescue

Отзывы:

Похожие инструкции для MS 461 Rescue

Бренды по названию

Популярные бренды