background image

MS 461

English

16

N

Start felling cut using plunge-cut 

method.

N

Enlarge felling cut as far as 

hinge (4).

Do not cut into the hinge.

N

Enlarge felling cut as far as 

stabilizing strap (5).

Do not cut into the stabilizing strap.

N

Insert a felling wedge (6).

Shout a second warning immediately 

before the tree falls.

N

Holding the saw with outstretched 

arms, cut through the stabilizing 

strap horizontally at the same level 

as the felling cut.

Felling Cut with Holding Strap (Leaner)

A) Small diameter trees
Perform this felling cut when the tree 

diameter is smaller than the length of the 

guide bar.

N

Plunge the guide bar into the trunk 

until it emerges at the other side.

N

Enlarge the felling cut (E) in 

direction of hinge (1).

Cut horizontally.

Do not cut into the hinge.

N

Enlarge the felling cut in direction of 

holding strap (2).

Cut horizontally.

Do not cut into the holding strap.

Shout a second warning immediately 

before the tree falls.

N

Cut through the holding strap at a 

downward angle from outside with 

outstretched arms.

6.

001BA274 KN

1.

2.

001BA265 KN

001BA266 KN

Содержание MS 461 Rescue





















































Отзывы: