Stihl MS 461 Rescue Скачать руководство пользователя

Страница: 27 / 52

MS 461

English

Locking the chain

–

in an emergency

–

when starting

–

at idling speed

The chain brake is activated by pushing

the hand guard toward the bar nose with

your left hand – or by inertia in certain

kickback situations: The chain is

stopped and locked.

Releasing the chain brake

Pull the hand guard back toward the

front handle,

NOTICE

Always disengage chain brake before

accelerating the engine (except when

checking its operation) and before

starting cutting work.
High revs with the chain brake engaged

(chain locked) will quickly damage the

powerhead and chain drive (clutch,

chain brake).
The chain brake is also activated by the

inertia of the front hand guard if the

kickback force of the saw is high

enough: The hand guard is accelerated

toward the bar nose – even if your left

hand is not behind the hand guard, e.g.

during felling cut.

The chain brake will operate only if the

hand guard has not been modified in any

way.

Check operation of the chain brake

Before starting work: Run engine at idle

speed, engage the chain brake (push

hand guard toward bar nose) and open

the throttle wide for no more than

3 seconds – the chain must not rotate.

The hand guard must be free from dirt

and move freely.

Chain brake maintenance

The chain brake is subject to normal

wear. It is necessary to have it serviced

and maintained regularly by trained

personnel. STIHL recommends that you

have servicing and repair work carried

out exclusively by an authorized STIHL

servicing dealer. Maintain the following

servicing intervals:

Chain Brake

143BA011 KN

143BA012 KN

Full-time usage:

every 3

months

Part-time usage:

every 6

months

Occasional usage:

every 12

months

Содержание MS 461 Rescue





















































Результаты поиска

Содержание MS 461 Rescue

Отзывы:

Похожие инструкции для MS 461 Rescue

Бренды по названию

Популярные бренды

Stihl MS 461 Rescue, Инструкция по эксплуатации

Результаты поиска

Содержание MS 461 Rescue

Отзывы:

Похожие инструкции для MS 461 Rescue

Бренды по названию

Популярные бренды