STIEBEL ELTRON WSG-2-DUO, Руководство администратора по эксплуатации и установке

Страница: 5 / 28

ENGL
IS
H
iNSTallaTiON
PrOFi SElECT modular system
WSP-2-DUO, WSG-2-DUO | 5
8.1 Base station
Base stations are fully functional apartment modules which
can be further equipped with output modules and installation
options.
Designation Description
WSP-2-DUO Copper-soldered heat exchanger,
integral instantaneous water heater
WSG-2-DUO Stainless steel-soldered heat exchanger,
integral instantaneous water heater
D
00000
75
08
6
1
4
3
2
5
6
10
11
12
9
7
8
1 air vent screw
2 Mounting position on finished walls
3 Mounting position on unfinished walls
4 room heating valve
5 Differential pressure controller
6 Heat meter adaptor
7 Equipotential bonding connection
8 Pressure surge reducer
9 instantaneous water heater
10 Plate heat exchanger
11 Dirt filter with strainer
12 "Thermo Fluid System" (TFS) temperature controller
Note
There are no output modules available for the WSP-2-
DUO and WSG-2-DUO base stations.
8.1.1 Heat meter
Heat meters must be installed in the unit on site.
The base units are equipped with appropriate fittings (110 mm,
¾” 1.5 m³/h) for the heat meters.
Sensor retainer:
- Directly immersed
- Sensor length: 28 mm
- Diameter: Max. 5.4 mm; at the sealing point min. 5.2 mm
8.1.2 Heat exchanger operating conditions
The threaded, stainless steel soldered heat exchanger is par-
ticularly suitable for applications where water quality is critical.
Water constituents /
characteristic values
Unit Heat exchanger
copper soldered
Heat exchanger
stainless steel sol-
dered
pH value 7-9 (taking Si index
into account)
6-10
Saturation index Si
(delta pH value)
-0.2 < 0 < +0.2 Not specified
Total hardness °dH 6-15 6-15
Conductivity μS/cm 10...500 Not specified
Suspended solids mg/l < 30 < 30
Chloride mg/l above 100 °C no chlorides permissible
Free chlorine mg/l < 0.5 < 0.5
Hydrogen sulphide mg/l < 0.05 Not specified
ammonia mg/l < 2 Not specified
Sulphate mg/l < 100 < 400
Hydrogen carbonate mg/l < 300 Not specified
Hydrogen carbonate/
sulphate
mg/l > 0.1 Not specified
Sulphide mg/l < 1 < 7
Nitrate mg/l < 100 Not specified
Nitrite mg/l < 0.1 Not specified
iron, dissolved mg/l < 0.2 < 0.2
Manganese mg/l < 0.1 Not specified
Free, aggressive carbon
dioxide
mg/l < 20 Not specified
Note
We recommend using a softening system if the total
hardness is > 15 °dH.
8.1.3 Thermal overflow valve operating conditions
a thermal overflow valve can be used at the end of the line to
increase comfort levels.
Designation Part number
Overflow valve
ÜVS 236016
Note
if the simple pipe length (see following table) of the
last heat interface unit in the line is not exceeded, a
thermal overflow valve is not required.
Required flow temperature [°C] 70 65 60 55
Nominal pipe diameter Pipe length [m]
DN 15 21 17 12 7
DN 20 18 15 11 6
DN 25 16 13 9 5
DN 32 14 11 8 5
DN 40 13 10 7 4
DN 50 11 9 7 4