-2-
Contact Rating (Resistive)
Specifications
- 30V AC/DC, 1A
- Standby Power: 12VDC, 10mA
- Max Operating: 12VDC, 16mA
MODE
SWITCH POSITIONS
Program
Latching
Auto Restore
Antenna
Sounder
Yellow Reset
Leads
+
_
NC
COM
NO
PROGRAM
SOUNDER LED
RELAY
Power ON in program
Start-Up tone will sound
Alernating RED and GREEN
Normal
Activate transmitter
Will double beep
Alternating RED and GREEN
Normal
LATCHING
SOUNDER LED
RELAY
Power ON in latching (normal)
Start-up tone will sound
Flash GREEN every 2-3 seconds Normal
Activate transmitter
Will double beep
Solid RED
Switched
Transmitters restores
No sound
Flashing RED
Switched
AUTO RESTORE
SOUNDER
LED
RELAY
Power ON in auto restore (normal)
Start-Up tone will sound
Flash GREEN every 2-3 seconds Normal
Activate transmitter
Will double beep
Solid RED
Switched
Transmitter restores
No sound
Flash GREEN every 2-3 seconds Normal
Modes of Operation
{
12VDC
-3-
Instructions
Move switch to program. LED will flash RED and GREEN. Program transmitter into receiver by activating
transmitter (see transmitter instructions). Speaker will double beep to confirm programming. Move mode
switch to intended mode. Activate transmitter to confirm enrollment.
To operate in Latching
- Move switch to center position. The LED will turn GREEN and flash every 2-3
seconds.
When activated in Latching
- Sounder will double beep and LED will turn to solid RED state. When
restore signal is received from transmitter LED will flash RED.
Options for restoring the receiver (LED flashing RED)
• Move slide switch to Auto Restore (bottom position) and then back to Latching.
• Use Keyfob (STI-34106) - press the OFF button and then press the ON button.
• Hard-wire the momentary switch to yellow reset leads on receiver and cycle switch.
To operate in Auto Restore
– Move switch to bottom position. The LED will flash GREEN every 2-3
seconds. When activated in Auto Restore, LED will go solid RED until the restore transmission is received.
Once received, the LED will flash GREEN.
Keyfob Operation with STI-34098 Receiver
Keyfob has 2 functions:
• ON/OFF – can be used to reset latched receiver to normal after the restore signal is sent.
• RED and WHITE buttons can be used as alert transmitter.
· RED button sends alert signal.
· WHITE button sends restore signal.
Programming Keyfob in Receiver
Move switch to Program Mode. LED flashes alternating RED/GREEN.
Program ON/OFF reset function
– press ON and OFF buttons at the same time to enroll.
Receiver will beep twice to acknowledge enrollment.
Enrolling the keyfob will delete any previously enrolled keyfob.
Program RED/WHITE buttons
– while in Program Mode, press the RED and WHITE buttons
simultaneously. The receiver will beep twice to acknowledge enrollment. The RED and WHITE buttons
function as a transmitter. Programming these buttons will delete previously programmed transmitters.
Supervisory signal
(3 Types) - Flashing Amber LED (RED and GREEN flashing together) and the sounder
will beep once every minute. Signal will show up within 18-24 hours.
1. Tamper on transmitter is open.
2. Low battery signal from transmitter.
3. Transmitter is out of range.
Notes
• STI-34098 receives signal from only one transmitter.
• Attempting to program a second transmitter will delete original transmitter.
• If receiving a signal from another 433.92 MHz transmitter, the LED will flash GREEN for 3-5seconds.
• Professional installation only.
Warranty Information
Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall
be free of defects in material and workmanship under normal use and circumstances for a period of one
(1) year from the original date of purchase.
Electronic warranty form at www.sti-usa.com/wc14.
