manualshive.com logo in svg

STI Prep/Master 2807, Руководство по эксплуатации

Поделиться
Скачать
STI Prep/Master 2807 Скачать руководство пользователя страница 25

Operating Manual

STI-2807  |  STI-2818LP

23

8.2 

Diagnosis of Electrical Failure

Prior to any repair work on the machine or drives, the machine must be secured against 

unintentional start-up. Put the machine in its Safety-off position.

Work on electrical equipment may only be undertaken by a skilled electrician or by 

trained persons under supervision of a skilled electrician in accordance with electrical 

engineering regulations.

Failure

Possible Reasons for Failure

Corrective Actions

Motor does not 

start up

Missing Phase

Check power supply

Faulty switch or relays

Get diagnosis and replacement by a 

skilled electrician

Emergency Stop 

Unlock the emergency stop button

Motor stops 

during operation

Current power is too high.

Disconnect plug.

Supply circuit breaker is disengaged. Reset circuit breaker or replace fuse.
Motor is damaged.

Inspect motor.

8.3 

Programming the SMV Drive for the P/M Machine

In cases of tampering or random malfunction, the SMV drive will require the following programming: 

1) Master Reset, and 2) STI Settings.
In the case of an SMV drive being repaired and returned to you, the SMV drive will require the 

following programming: 1) STI Settings.

SMV Drive - Master Reset Procedure (standard factory settings):

1.  With SMV Drive powered on, press M on the keypad.

2.  Press the arrow up key to scroll to the number "0225." Press M. The display will read "P100".

3.  Press the arrow up key to "P199". Press M. Screen will display “00”.

4.  Arrow up to "03". Press M.

5.  Unplug the machine from the source power or turn off the red/yellow switch and allow the 

drive to power down for at least one minute.

6.  Plug the machine back into source power or switch on the red/yellow switch to power up.

SMV Drive - STI Settings Procedure:

1.  With SMV Drive powered on, press M on the keypad.

2.  Press the arrow up key to scroll to the number "0225". Press M.

3.  Press arrow up and scroll to “P104”. Press M. Screen will display “20.0”.

4.  Arrow down and scroll to “5.0”. Press M. Screen will display “P104”.

5.  Arrow up and scroll to “P112”. Press M. Screen will display “0.0”.

6.  Arrow up to “01”. Press M. Screen will display “P112”. 

7.  Arrow up to “P121”. Press M. Screen will display “00”.

8.  Arrow up to “21”. Press M.

At this point, the machine will be programmed and ready for use with its STI settings.

Содержание Prep/Master 2807





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды