STI PR-7505 Скачать руководство пользователя

Страница: 6 / 16

ASSEMBLE INSTRUCTIONS

STEP 7

a. Attach the

Left Pedal Support Arm

(10)

onto the

Left Pivoting Arm (8)

and secure

with the

1x Button Head

Bolt (M10xp1.5x85mm) (90)

and

1 x

Nylon lock Nut (M10xp1.5) (104).

b. Press the

Nut Cap (105)

onto the

Nylon lock Nut (M10xp1.5) (104).

c. Repeat the above procedure to attach

the

Right Pedal Support Arm (11)

onto the

Right Pivoting Arm (9).

Note:

make sure the bolts are fully

tightened to avoid noise

STEP 8

a. Please go back to fully tighten with the

2 x

Hex Head Bolts

(M10xp1.5x50mm) (95)

and the 2 x Lock nuts

(103)

with the

T-Handle

SOCKET WRENCH

(17mm)

as shown.

b. Attach the

Front Decorative Upright Cover

(21)

onto the front of the

Main Frame (1)

with the

2 x Round Head Screws

(M5xp0.8x50mm) (81).

c. Place the Logo Sticker on the surface of the

Front Decorative Upright Cover (21).



A logo sticker is located in one of the hardware boxes.

d. Slide the

Upright Sleeve (22)

down to cover the open area of the

Main Frame (1).

NOTE: Please make sure Bolts (90) are

inserted from the inside of the Pivoting Arm

and the Nuts (104) and Nut Caps (105) are

installed from the outside

Содержание PR-7505

















Результаты поиска

Содержание PR-7505

Отзывы:

Похожие инструкции для PR-7505

Бренды по названию

Популярные бренды

STI PR-7505, Руководство пользователя

Результаты поиска

Содержание PR-7505

Отзывы:

Похожие инструкции для PR-7505

Бренды по названию

Популярные бренды