background image

 

13 

                                                                                                                                                           

PARTS LIST 

NO. 

Item Name 

Q'TY 

1  Main Frame 

2  Front Stabilizer 

3  Rear Stabilizer 

4  Upright Post 

5  Stationary Handlebar 

6  Left Upper Handlebar 

7  Right Upper Handlebar 

8  Left Pivoting Arm 

9  Right Pivoting Arm   

10  Left Pedal Support Arm 

11  Right Pedal Support Arm 

12  Front Left-Side Cover 

13  Front Right-Side Cover 

14  Rear Left-Side Cover 

15  Rear Right-Side Cover 

16  Main Frame Base Cover 

17  Console 

18  Console Bracket 

19  Console Lower Case 

20  Battery Door 

21  Front Decorating Upright Cover 

22  Upright Sleeve 

23  Accessory Tray 

24  Pulse Sensor Top Housing 

25  Pulse Sensor Bottom Housing 

26  Pulse Sensor Plate Assembly 

27  Foam Grip Assembly (40mm) 

28 

Stationary Handlebar Plug 
(ψ31.8mm) 

29  Foam Grip Assembly (225mm) 

30  Inner Rotator Cuff-Pivoting Arm 

31  Front Rotator Cuff-Pivoting Arm 

32  Back Rotator Cuff-Pivoting Arm 

33  Pedal Upper Case 

34  Non-Slip Pad 

NO. 

Item Name 

Q'TY 

35  Roller 

36  EndCap (50x100mm) 

37  Pulley (120mm) 

38  Pulley (235mm) 

39  Magnet 

40  Belt (1126mm J8) 

41  Belt (1059mm J8) 

42  Square Plug   

43  Console Fixed Bracket 

44  Front Aluminum Upright Cover 

45  Back Aluminum Upright Cover 

46  Upper Pivot Shaft Spacer 

47  Pedal Arm Spacer 

48  Linkage Spacer 

49  Left Crank 

50  Right Crank 

51  Crank Axle 

52  Mounting Plate 

53  Generator   

54  Controller 

55  Resistor 

56  Drive Shaft 

57  Bearing Stand 

58  Leveler 

59  Pedal Support Arm Connector 

60  Bearing (6004) 

12 

61  Bearing (6905) 

62  Eye Bolt 

63  Tension Bracket 

64  C Ring 

65  Square Key   

66  Lock Washer (M8) 

17 

67  Washer (8x26x2.0t) 

68  Washer (8x23x2.0t) 

69  Washer (8x30x2.0t) 

Содержание PR-7505

















Отзывы: