Steris P920011-649 Скачать руководство пользователя страница 55

Страница: 55 / 168

4-10

920011-649

Operator Manual

Processing Instructions

Carefully

feed distal tip of insertion tube into split insertion

tube sleeve (see Figure 4-9).

c. When split insertion tube sleeve is located further up

insertion tube, away from distal tip bigger end, close sleeve

carefully

around insertion tube (see Figure 4-10).

Carefully

slide split insertion tube sleeve to other end of

insertion tube, near control handle.

IMPORTANT: Refer to

Endoscope Quick Reference Guide

to ensure there are no special placement instructions
required for the endoscope being processed.

NOTE:

Verify angulation knobs are unlocked and distal tip is

straight before proceeding to next step.

e. Carefully feed distal end of insertion tube into insertion tube

slide (see Figures 4-6 and 4-7). Feed nearly all insertion tube

and, when control handle is located over control handle boot,

leave control handle to rest on control handle boot frame.

IMPORTANT: Hold insertion tube near control handle boot
opening to ease insertion and prevent damage caused by
kinking or excessive bending.

NOTE:

For insertion tubes that are hard to insert, wet tube

with water to ease insertion.

Split Insertion Tube Sleeve

Distal Tip

Push Down Sleeve Handle

Figure 4-9. Feeding Distal Tip Into Sleeve

Figure 4-10. Closing Sleeve Around Insertion Tube

Split Insertion Tube Sleeve

Insertion Tube (Inserted

Over Sleeve Handle)

Push Down Sleeve Handle

Содержание P920011-649









































































































































































Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды

Steris P920011-649, Руководство оператора

Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды