Steris P920011-649 Скачать руководство пользователя страница 54

Страница: 54 / 168

4-9

Processing Instructions

Operator Manual

920011-649

b. Carefully feed distal end of insertion tube into insertion tube

slide

(see Figures 4-6 and 4-7)

Feed entire insertion tube

into slide.

IMPORTANT: Hold insertion tube near control handle boot
opening to ease insertion and prevent damage caused by
kinking or excessive bending.

NOTE:

For insertion tubes that are hard to insert into tube

slide, wet tube with water to ease insertion.

12.

If using split insertion tube sleeve (NOT labeled with a color
dot),

proceed as follows (see

Figure 4-8)

a. Open split insertion tube sleeve as shown in Figure 4-8.

CAUTION –

POSSIBLE EQUIPMENT

DAMAGE:  Do  not  place  light
guide/ultrasound  connectors
on  their  cables  or  damage
may result.

Figure 4-6. Insert Insertion Tube Into Control

Handle Boot Opening

IMPORTANT:

Hold Insertion Tube Near Control Handle Boot

Opening to Prevent Excessive Bending or Kinking.

Insertion Tube

Control

Handle

Light Guide Cable

Control Handle

Boot Opening

Figure 4-7. Place Control Handle in Control

Handle Boot

Universal

Cord Port

Flaps

Light

Guide

Cable

Strain

Relief

Boot

Insertion

Tube

Slide

Endoscope Control

Handle

Figure 4-8. Split Insertion Tube Sleeve

WITHOUT a Color

Identification

Opening Split Insertion Tube Sleeve

Содержание P920011-649









































































































































































Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды

Steris P920011-649, Руководство оператора

Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды