SteppIR SARK-110 Скачать руководство пользователя страница 16

Страница: 16 / 78

SteppIR

SARK-110

User’s Manual

Rev 1.1.7 October 29

, 2014

- 16 -

© Melchor Varela – EA4FRB 2011-2014

4.8 Changing the Vertical Axis Parameter

In Scalar Chart mode, the

SteppIR

SARK-110 can display two traces from any of the available

parameters for the vertical axis. Use Navigator A to highlight either

«LeftY»

«RightY»

in the main

menu.

There are two methods of changing the selected vertical axis parameter:

(i)

Press the Select

[

■

]

button to activate the LeftY or RightY popup submenu. Use Navigator B to

highlight the desired submenu parameter option. Press the Select

[

■

]

button to validate the

selection. Press any other button to cancel the operation.

The screenshot below show the available parameters for the vertical axis:

(ii)

Use Navigator B when either the

«LeftY»

«RightY»

option is highlighted. Options are

selected sequentially.

Содержание SARK-110















































































Результаты поиска

Содержание SARK-110

Отзывы:

Бренды по названию

Популярные бренды

SteppIR SARK-110, Руководство пользователя

Результаты поиска

Содержание SARK-110

Отзывы:

Бренды по названию

Популярные бренды