SteelMax Rail Runner LT Скачать руководство пользователя страница 8

Страница: 8 / 53

Rail Runner LT

Rail Runner LT

– Operator’s Manual

24. Before every use, make sure that the carriage is not damaged and no part is

cracked or loose. Make sure to maintain correct conditions that can affect the

operation of the carriage.

25. Do not try to stop the travel by hand. To stop, set the travel direction switch to

‘O’.

26. Maintain only after you unplug the carriage from the power source.

27. Repair only in a service center appointed by the seller.

28. If the carriage falls from any height, is wet, or has any damage, stop the work and

promptly send the carriage to the service center for check and repair.

29. Do not leave the carriage unattended during work.

30. When the carriage is not in use, remove it from

the

worksite

and

keep

a safe

and

dry place.

Содержание Rail Runner LT






















































Результаты поиска

Содержание Rail Runner LT

Отзывы:

Похожие инструкции для Rail Runner LT

Бренды по названию

Популярные бренды

SteelMax Rail Runner LT, Руководство оператора

Результаты поиска

Содержание Rail Runner LT

Отзывы:

Похожие инструкции для Rail Runner LT

Бренды по названию

Популярные бренды