SteelMax Rail Runner LT Скачать руководство пользователя

Страница: 7 / 53

Rail Runner LT

Rail Runner LT

– Operator’s Manual

2. SAFETY PRECAUTIONS

1. Before starting

, read this Operator’s Manual and complete occupational safety and

health training.

2. Use

only in applications specified in this Operator’s Manual.

3. Make

sure

that

the

carriage

complete

and

all

parts are genuine and not damaged.

4. Make sure that the specifications of the power source are the same as those

specified on the rating plate.

5. Connect the carriage to a correctly grounded power source.

6. Do not carry the carriage by the cords or cables, and do not pull them. This can

cause damage and electric shock.

7. Keep untrained bystanders away from the carriage.

8. Before starting, ensure the correct condition of the carriage, power source, cords,

arc ignition cable, connections, rollers, and gear.

9. Keep

the

carriage dry. Do not expose it to rain, snow, or frost.

10. Keep the work area well lit, clean, and free of obstacles.

11. Do not use near flammable materials, or in explosive environments.

12. Transport and position the carriage by using the carrying handles.

13. Install the carriage only on the supplied track.

14. Make sure that the gear and rollers are clean.

15. Plug the cords and arc ignition cable into sockets only when the power switch is

set to

‘O’.

16. Keep the sockets clean. Do not use high pressure during cleaning.

17. Install only torches whose diameter matches the diameter of the torch holder.

18. Suspend cables to reduce the load of the carriage.

19. Do not bend the semi-flexible track to a radius less than

5 m (16 ft).

20. Use the rigid track only on flat surfaces.

21. At heights, protect the carriage and the track from falling. To do this, use chains

(not included) to attach the leftmost and rightmost magnetic units of the semi-

flexible or rigid track to a stable structure. To protect the carriage, attach a chain to

a carrying handle. The chains must not be loose.

22. Do not stay below the carriage or the track that is put at heights.

23. Use

eye

protection

(helmet,

shield,

and

screen),

hearing protection, gloves, and

protective clothing during work. Do not use loose clothing.

Содержание Rail Runner LT






















































Результаты поиска

Содержание Rail Runner LT

Отзывы:

Похожие инструкции для Rail Runner LT

Бренды по названию

Популярные бренды

SteelMax Rail Runner LT, Руководство оператора

Результаты поиска

Содержание Rail Runner LT

Отзывы:

Похожие инструкции для Rail Runner LT

Бренды по названию

Популярные бренды