SteelMax D1 AUTO Скачать руководство пользователя страница 23

Страница: 23 / 23

D1 Operator’s Manual

9. WARRANTY CARD

WARRANTY CARD No

.............

..................................................................... in the name of Manufacturer warrants the

D1 Drilling Machine with Electromagnetic

Base to be free of defects in material and

workmanship under normal use for a period of 12 months from the date of sale.

This warranty does not cover cutters as well as damage or wear that arise from

misuse, accident, tempering or any other causes not related to defects in workmanship

or material.

Date of production .........................................................................................................

Serial number ................................................................................................................

Date of sale ...................................................................................................................

Signature of seller ..........................................................................................................

1.03 / 17 May 2017

WE RESERVE THE RIGHT TO MAKE CHANGES IN THIS MANUAL WITHOUT NOTICE

Содержание D1 AUTO
























Результаты поиска

Содержание D1 AUTO

Отзывы:

Похожие инструкции для D1 AUTO

Бренды по названию

Популярные бренды

SteelMax D1 AUTO, Руководство оператора

Результаты поиска

Содержание D1 AUTO

Отзывы:

Похожие инструкции для D1 AUTO

Бренды по названию

Популярные бренды